lilo

[Tomasz Kłoczko]

Mam pewien kłopot z nowym lilo:

# lilo

LILO is unable to correctly determine the device codes assigned to two
of your disks by the System BIOS.  Consequently, it seems to have guessed
wrong.  The following conflict needs to be resolved with explicit
    "disk=/dev/...  bios=0x??" lines in '/etc/lilo.conf'.

Fatal: Bios device code 0x81 is being used by two disks
        /dev/ataraid/disc0/disc (0x7200)  and
/dev/ide/host2/bus0/target0/lun0/disc (0x2100)

# cat /proc/partitions
major minor  #blocks  name

 114     0  156301312 ataraid/disc0/disc
 114     1    4297356 ataraid/disc0/part1
 114     4          1 ataraid/disc0/part4
 114     5    4297356 ataraid/disc0/part5
 114     6  142343901 ataraid/disc0/part6
 114     7    4610623 ataraid/disc0/part7
 114     8     746991 ataraid/disc0/part8
  34     0   78150744 ide/host2/bus1/target0/lun0/disc
  33     0   78150744 ide/host2/bus0/target0/lun0/disc
  33     1    4297356 ide/host2/bus0/target0/lun0/part1
  33     4          1 ide/host2/bus0/target0/lun0/part4   
   3     0   29888820 ide/host0/bus0/target0/lun0/disc
   3     1   29888680 ide/host0/bus0/target0/lun0/part1

ICH4: BIOS setup was incomplete.
ICH4: chipset revision 1
ICH4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:pio
PDC20276: IDE controller on PCI bus 02 dev 10
PCI: Found IRQ 9 for device 02:02.0
PCI: Sharing IRQ 9 with 02:0a.0
PDC20276: chipset revision 1
PDC20276: not 100% native mode: will probe irqs later
PDC20276: (U)DMA Burst Bit ENABLED Primary MASTER Mode Secondary MASTER 
Mode.
    ide2: BM-DMA at 0x9400-0x9407, BIOS settings: hde:pio, hdf:pio
    ide3: BM-DMA at 0x9408-0x940f, BIOS settings: hdg:pio, hdh:pio
hda: ST330630A, ATA DISK drive
hdc: PIONEER DVD-RW DVR-104, ATAPI CD/DVD-ROM drive
hde: ST380021A, ATA DISK drive
hdg: ST380021A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
ide2 at 0xa800-0xa807,0xa402 on irq 9
ide3 at 0xa000-0xa007,0x9802 on irq 9
blk: queue e08251a4, I/O limit 4095Mb (mask 0xffffffff)
hda: 59777640 sectors (30606 MB) w/2048KiB Cache, CHS=59303/16/63, 
UDMA(33)
blk: queue e082586c, I/O limit 4095Mb (mask 0xffffffff)
hde: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=155061/16/63, 
UDMA(100)
blk: queue e0825bd0, I/O limit 4095Mb (mask 0xffffffff)
hdg: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=155061/16/63, 
UDMA(100)
Partition check:
 /dev/ide/host0/bus0/target0/lun0: p1
 /dev/ide/host2/bus0/target0/lun0: [PTBL] [9729/255/63] p1 p4 < >
 /dev/ide/host2/bus1/target0/lun0: unknown partition table
 ataraid/d0: p1 p4 < p5 p6 p7 p8 >
Drive 0 is 76319 Mb (33 / 0) 
Drive 1 is 76319 Mb (34 / 0) 
Raid0 array consists of 2 drives. 
Promise Fasttrak(tm) Softwareraid driver for linux version 0.03beta

lilo.conf na którym ot do tej pory chodziło:

boot=/dev/hda
map=/boot/map
install=/boot/boot.b
prompt
timeout=50
vga=5

root=/dev/ataraid/disc0/disc

image=/boot/vmlinuz-2.4.20-0.1
        label=linux-2.4.20
        initrd=/boot/initrd-2.4.20-0.1.gz

W dokumentacj ido lilo jakoś nie nadziałem sie na nic co mogłoby świadczyć 
o tym że należąłoby po ostanichj zmianach wykonac jakeiś zmiany w 
lilo.conf. Ktos kojarzy powyśze z czymś co mogłoby wskazywać na to że nie 
jest to jednak byk w lilo z którym należy walić do maintainera ?

kloczek
-- 
-----------------------------------------------------------
*Ludzie nie mają problemów, tylko sobie sami je stwarzają*
-----------------------------------------------------------
Tomasz Kłoczko, sys adm @zie.pg.gda.pl|*e-mail: kloczek w rudy.mif.pg.gda.pl*