[announce] PLD InstallCD v0.1-1

[Andrzej Zawadzki]

Arkadiusz Patyk wrote:
> Andrzej Zawadzki (zawadaa w gmail.com) wrote:
> 
>>Marcin Doliński wrote:
>>
>>>W związku z zapotrzebowaniem na małą płytkę bazującą na kernelu 2.6 oraz 
>>>zawierającą sterowniki do popularnych kart radiowych (rt2[45]00, madwifi, 
>>>acx100, ipw2[12]00) powstała płytka InstallCD. Nie posiada ona automatycznej 
>>>detekcji niczego poza kontrolerami IDE/SCSI/SATA.
>>
>>Nie obsługuje IDE/SATA na płycie:
>>GA-K8NF-9 - nie może podmontować cdroma
>>Dziwne trochę bo staaare rescuecd na 2.4 działa (tylko ide)
> 
> 
> ciekawe jak sobie poradzi nowsze ;)
> możesz sprawdzić ?
> http://rescuecd.pld-linux.org/alfa/rescue.iso
Oczywiście, że mogę, a nawet muszę ;-)
Działa ślicznie:


SCSI subsystem initialized
libata version 1.10 loaded.
sata_nv version 0.6
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [APSI] -> GSI 20 (level,
low) -> IRQ 50
PCI: Setting latency timer of device 0000:00:07.0 to 64
ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xD000 irq 50
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xD008 irq 50
ata1: dev 0 cfg 49:2f00 82:346b 83:7f61 84:4003 85:3468 86:3c41 87:4003
88:407f
ata1: dev 0 ATA, max UDMA/133, 312579695 sectors: lba48
nv_sata: Primary device added
nv_sata: Primary device removed
nv_sata: Secondary device added
nv_sata: Secondary device removed
ata1: dev 0 configured for UDMA/133
scsi0 : sata_nv
ata2: no device found (phy stat 00000000)
scsi1 : sata_nv
  Vendor: ATA       Model: WDC WD1600JD-00H  Rev: 08.0
  Type:   Direct-Access                      ANSI SCSI revision: 05
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [APSJ] -> GSI 23 (level,
low) -> IRQ 217
PCI: Setting latency timer of device 0000:00:08.0 to 64
ata3: SATA max UDMA/133 cmd 0x9E0 ctl 0xBE2 bmdma 0xE400 irq 217
ata4: SATA max UDMA/133 cmd 0x960 ctl 0xB62 bmdma 0xE408 irq 217
ata3: no device found (phy stat 00000000)
scsi2 : sata_nv
ata4: no device found (phy stat 00000000)
scsi3 : sata_nv
SCSI device sda: 312579695 512-byte hdwr sectors (160041 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 312579695 512-byte hdwr sectors (160041 MB)
SCSI device sda: drive cache: write back
 /dev/scsi/host0/bus0/target0/lun0: p1 p2 < p5 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0

a tu IDE

ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE-CK804: IDE controller at PCI slot 0000:00:06.0
NFORCE-CK804: chipset revision 162
NFORCE-CK804: not 100% native mode: will probe irqs later
NFORCE-CK804: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE-CK804: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE-CK804: 0000:00:06.0 (rev a2) UDMA133 controller
    ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: WDC WD800JB-00JJC0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: LITE-ON DVDRW SOHW-1633S, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: Host Protected Area detected.
        current capacity is 156299375 sectors (80025 MB)
        native  capacity is 156301488 sectors (80026 MB)
hda: Host Protected Area disabled.
hda: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=65535/16/63,
UDMA(100)
hda: cache flushes supported
 /dev/ide/host0/bus0/target0/lun0: p1
hdc: ATAPI 32X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20

i jeszcze karta sieciowa dla porządku bo to też hackowany kawałek kodu ;-)

forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.31.
ACPI: PCI Interrupt Link [APCH] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [APCH] -> GSI 21 (level,
low) -> IRQ 233
PCI: Setting latency timer of device 0000:00:0a.0 to 64
eth0: forcedeth.c: subsystem: 01458:e000 bound to 0000:00:0a.0
eth0: no link during initialization.

Dziękuję - odzyskam bez przekładania sprzętu troszkę danych :-)

-- 
Andrzej Zawadzki