2 problemy

Zupa aka Tyler tyler w netbox.pl
Wto, 30 Kwi 2002, 19:49:01 CEST


W liście z wto, 30-04-2002, godz. 19:34, Krzysiek Taraszka pisze: 

> ok, to teraz podaj wynik cat /etc/sysconfig/interfaces/ifcfg-eth0 i 

[root w moje /root]# cat /etc/sysconfig/interfaces/ifcfg-eth0
# example config for first ethernet card

# name of the device
DEVICE="eth0"

# IP addresses/address prefix
# where prefix:
# 24 - resembles netmask 255.255.255.0
# 16 - resembles netmask 255.255.0.0
# etc.
# IPADDR may be either IPv4 or IPv6
# you may have up to 256 addresses set up
IPADDR=""
#IPADDR1=192.168.0.2/24
#IPADDR2=192.168.0.3/24
#IPADDR3=192.168.0.4/24

# you may select which of the above addresses
# is primary for this interface (it'd be IPADDR1 in the example below)
#IP4_PRIM_IF="1"

# activate on boot? yes|no
# you must set it to 'yes' if you want to have this up after bootup
ONBOOT="yes"

# dhcp|pump|none
BOOTPROTO="none"
# Added by installer
PREFIX=""


> /etc/sysconfig/network.

[root w moje /root]# cat /etc/sysconfig/network
# $Id: network,v 1.15 2001/11/05 16:58:50 kloczek Exp $
######################################################################
# MAIN PART

# Do you need IPv4 or IPv6 networking ?
NETWORKING=yes

# Do you need IPv4 networking ?
IPV4_NETWORKING=yes

# Do you want IPv4 forwarding ?
IPV4_FORWARDING=no

# Set hostname here (only hostname)
HOSTNAME="moje"

# Set NIS domain name here
NISDOMAIN="localdomain"

# IPv4 gateway
GATEWAY="192.168.1.1"
GATEWAYDEV="eth0"

# Do you want to use IPX networking ?
IPX=no
IPXAUTOPRIMARY=
IPXAUTOFRAME=
IPXINTERNALNETNUM=
IPXINTERNALNODENUM=

# Do you need IPv6 networking ?
IPV6_NETWORKING=no

# Do you want IPv6 forwarding ?
IPV6_FORWARDING=no

# Enable tunnel interfaces configuration ?
IPV6_TUNNELCONFIG=no

# IPv6 gateway
GATEWAY6=
GATEWAY6DEV=

# Global route for IPv6 host with IPv6 forwarding
IPV6_GLOBALROUTEGW=
IPV6_GLOBALROUTEDEV=

# Reading configuration from LDAP

# Do you want to use LDAP?
USE_LDAP=no

# What base DN use for searching for interface configuration
LDAP_BASE_DN=

# Other

# Do you want set static ARP table (based on /etc/ethers config file) ?
STATIC_ARP=no

# Do you want set static RARP table (based on /etc/ethers config file) ?
STATIC_RARP=no

# Specify interface on which you want to enable tleds software
# (also you need tleds package installed) -- default set to no
TLEDS_DEV=no

# This must be last line !
# vi:syntax=sh:tw=78:ts=8:sw=4

> Moze tam jest cos, jakis problem w maską bądź czymś :)
moze cos znajdziesz, ja nic nie widze ;/

 
> (karta+jajko raczej nie, sam mialem do niedawna tego rtla80129 na serverze 
> i bylo ok, teraz mam 3coma i jest tez ok)


Zupa





Więcej informacji o liście dyskusyjnej pld-users-pl