karta d-link dfe-580tx

[Papa]

Witam uprzejmie,

Sunday, January 11, 2004, 2:19:36 PM

Może ktoś wie dlaczego czteroportowa karta d-linka pracująca na module
sundance pluje takimi komunikatami:

Bringing up interface eth0.........................................[ DONE ]
Bringing up interface eth1.........................................[ DONE ]
RTNETLINK answers: File exists
Bringing up interface eth2.........................................[ DONE ]
RTNETLINK answers: File exists
Bringing up interface eth3.........................................[ DONE ]
RTNETLINK answers: File exists

divert: allocating divert_blk for eth0
eth0: D-Link DFE-580TX 4 port Server Adapter at 0xd000, 00:05:5d:7d:22:60, IRQ 4.
eth0: MII PHY found at address 1, status 0x7829 advertising 01e1.
divert: allocating divert_blk for eth1
eth1: D-Link DFE-580TX 4 port Server Adapter at 0xd400, 00:05:5d:7d:22:61, IRQ 10.
eth1: MII PHY found at address 1, status 0x7829 advertising 01e1.
divert: allocating divert_blk for eth2
eth2: D-Link DFE-580TX 4 port Server Adapter at 0xd800, 00:05:5d:7d:22:62, IRQ 5.
eth2: MII PHY found at address 1, status 0x7829 advertising 01e1.
divert: allocating divert_blk for eth3
eth3: D-Link DFE-580TX 4 port Server Adapter at 0xdc00, 00:05:5d:7d:22:63, IRQ 11.
eth3: MII PHY found at address 1, status 0x7829 advertising 01e1.
eth0: Link changed:
eth1: Link changed:
eth0: Link changed: 100Mbps, full duplex
eth2: Link changed:
eth3: Link changed:
eth1: Link changed: 100Mbps, full duplex
eth2: Link changed: 100Mbps, full duplex
eth3: Link changed: 100Mbps, full duplex

#lspci
02:04.0 Ethernet controller: D-Link System Inc DL10050 Sundance Ethernet (rev 14)
02:05.0 Ethernet controller: D-Link System Inc DL10050 Sundance Ethernet (rev 14)
02:06.0 Ethernet controller: D-Link System Inc DL10050 Sundance Ethernet (rev 14)
02:07.0 Ethernet controller: D-Link System Inc DL10050 Sundance Ethernet (rev 14)

# ip a
1: lo: <LOOPBACK,UP> mtu 16436 qdisc noqueue
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
2: eth0: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast qlen 1000
    link/ether 00:05:5d:7d:22:60 brd ff:ff:ff:ff:ff:ff
    inet 192.168.2.59/26 brd 192.168.2.63 scope global eth0
3: eth1: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast qlen 1000
    link/ether 00:05:5d:7d:22:61 brd ff:ff:ff:ff:ff:ff
    inet 192.168.2.60/26 brd 192.168.2.63 scope global eth1
4: eth2: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast qlen 1000
    link/ether 00:05:5d:7d:22:62 brd ff:ff:ff:ff:ff:ff
    inet 192.168.2.61/26 brd 192.168.2.63 scope global eth2
5: eth3: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast qlen 1000
    link/ether 00:05:5d:7d:22:63 brd ff:ff:ff:ff:ff:ff
    inet 192.168.2.62/26 brd 192.168.2.63 scope global eth3


Poza tym pracuje jak na razie poprawnie.
  

Pozdrowienia,
Andrzej                         mailto:awid w poczta.onet.pl