USB WIRELESS DONGLE SAGEM (od neostrady livebox)
Michał Panasiewicz
wolvverine w tarchomin.pl
Pią, 8 Wrz 2006, 02:09:09 CEST
Dnia 17-08-2006, czw o godzinie 21:22 +0200, Grzegorz Sójka napisał(a):
> Michał Panasiewicz wrote:
> > Dnia 17-08-2006, czw o godzinie 10:02 +0200, Grzegorz Sójka napisał(a):
> >> Michał Panasiewicz wrote:
> >>> pytanie dotyczace wynalazku z tematu, ktos ma to moze uruchomione na
> >>> PLD ??
> >>>
> >> Tak, Trzeba się trochę pomęczyć ale działa. A którą masz wersje? b czy
> >> g? Z g jest trochę prościej.
> >>
> > T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 8 Spd=12 MxCh= 0
> > D: Ver= 2.00 Cls=ff(vend.) Sub=ff Prot=ff MxPS=64 #Cfgs= 1
> > P: Vendor=079b ProdID=004a Rev=43.30
> > S: Manufacturer=ZyDAS
> > S: Product=802.11b/g USB WLAN
> > C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=500mA
> > I: If#= 0 Alt= 0 #EPs= 4 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
> > E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
> > E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
> > E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=1ms
> > E: Ad=04(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
> >
>
> Wpisz w google zd1211 (to symbol scalaka na którym to chodzi. W razie
> problemów napisz.
aktualnie nie chodzi WEP i WPA bez szyfrowania chodzi ladnie
w skrocie:
NA ROUTERZE -
# modprobe zd1211-bash-3.1# /etc/init.d/network start
ifcfg-eth0................................................................................................................[ DONE ]
Determining IP information for eth0
(dhcpcd)....................................................................................................[ DONE ]
Bringing up interface
ifcfg-eth1................................................................................................................[ DONE ]
Bringing up interface
ifcfg-wlan0...............................................................................................................[ DONE ]
Error for wireless request "Set Nickname" (8B1C) :
SET failed on device wlan0 ; Operation not supported.
-bash-3.1# cat /etc/sysconfig/interfaces/ifcfg-wlan0
DEVICE="wlan0"
IPADDR="10.0.1.1/24"
ONBOOT="yes"
BOOTPROTO="static"
WLAN_ESSID=34532454565433456889
#WLAN_KEY=s:xxxxxx
#WLAN_WPA=yes
WLAN_MODE=master
WLAN_NICKNAME="wolvvserv"
WLAN_BITRATE=auto
#WLAN_WPA_DRIVER=wext
#WLAN_WPA_DRIVER=zd1211
#WLAN_WPA_CONFIG=/etc/wpa_supplicant.conf
#WLAN_WPA_OPTIONS="-dd"
# sudo iwconfig wlan0
wlan0 802.11b/g NIC ESSID:"34532454565433456889"
Mode:Master Frequency=2.437 GHz Access Point:
00:60:B3:55:3E:3B
Bit Rate:11 Mb/s
Retry:off RTS thr=2432 B Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=84/100 Signal level=89/100 Noise level=0/100
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:2
Tx excessive retries:785 Invalid misc:0 Missed beacon:0
NA LAPTOPIE:
[adi w wolvv-lap ~]$ sudo modprobe ipw3945
[adi w wolvv-lap ~]$ sudo ipw3945d
[adi w wolvv-lap ~]$ sudo /etc/init.d/network start
Bringing up interface
ifcfg-lan0...................................[ FAIL ]
Determining IP information for lan0
(dhcpcd).......................[ FAIL ]
lan0: Check cable?
Bringing up interface
ifcfg-wlan0..................................[ DONE ]
Determining IP information for wlan0
(dhcpcd)......................[ DONE ]
[adi w wolvv-lap ~]$ sudo cat /etc/sysconfig/interfaces/ifcfg-wlan0
DEVICE=wlan0
#IPADDR=10.0.1.10/24
ONBOOT=yes
BOOTPROTO=dhcp
WLAN_ESSID=34532454565433456889
#WLAN_KEY=s:xxxxxx
#WLAN_WPA=yes
WLAN_MODE=Managed
WLAN_NICKNAME="wolvvnet"
WLAN_BITRATE=auto
#WLAN_WPA_DRIVER=wext
#WLAN_WPA_CONFIG=/etc/wpa_supplicant.conf
#WLAN_WPA_OPTIONS="-dd "
#
[adi w wolvv-lap ~]$ sudo iwconfig wlan0
wlan0 IEEE 802.11b ESSID:"34532454565433456889"
Nickname:"wolvvnet"
Mode:Managed Frequency:2.437 GHz Access Point:
00:60:B3:55:3E:3B
Bit Rate:11 Mb/s Tx-Power:15 dBm
Retry limit:15 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=91/100 Signal level=-39 dBm Noise level=-40 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:171 Missed beacon:0
po odhaszowaniu WLAN_KEY nie łączą się:
to samo po odhaszowaniu WPA
bez szyfrowania (syslog):
Sep 6 12:31:00 wolvverine kernel: usbcore: registered new driver zd1211
Sep 6 12:31:00 wolvverine kernel: zd1211:Switch to AP mode
Sep 6 12:31:00 wolvverine kernel: zd1211:Pure B-Mode
Sep 6 12:31:00 wolvverine kernel: zd1205: (enter)
zd1205_open, /home/users/adi/rpm/BUILD/zd1211-driver-r83/src/zd1205.c
line 4353
Sep 6 12:31:00 wolvverine kernel: zd1205: (exit)
zd1205_open, /home/users/adi/rpm/BUILD/zd1211-driver-r83/src/zd1205.c
line 4436
Sep 6 12:36:20 wolvverine kernel: zd1211:STA_ASSOCIATED with
00:13:02:xx:xx:xx
Sep 6 18:01:30 wolvverine kernel:
zd1211:STA_DISASSOCIATED:00:13:02:5f:49:83
Sep 8 00:48:40 wolvverine kernel: zd1211 - http://zd1211.ath.cx/ - r83
Sep 8 00:48:40 wolvverine kernel: zd1211:bulk out: wMaxPacketSize = 40
Sep 8 00:48:40 wolvverine kernel: zd1211:bulk in: wMaxPacketSize = 40
Sep 8 00:48:40 wolvverine kernel: zd1211:interrupt in: wMaxPacketSize =
40
Sep 8 00:48:40 wolvverine kernel: zd1211:interrupt in: int_interval = 1
Sep 8 00:48:40 wolvverine kernel: zd1211:bulk out: wMaxPacketSize = 40
Sep 8 00:48:40 wolvverine kernel: zd1211:USB Download Boot code success
Sep 8 00:48:40 wolvverine kernel: zd1211:MAC address =
00:60:b3:xx:xx:xx
Sep 8 00:48:40 wolvverine kernel: zd1211:AddrEntryTable = f7d4
Sep 8 00:48:40 wolvverine kernel: zd1211:RF_Mode = 00000104
Sep 8 00:48:40 wolvverine kernel: zd1211:Pure B-Mode
Sep 8 00:48:40 wolvverine kernel: zd1211:AllowedChannel = 000007ff
Sep 8 00:48:40 wolvverine kernel: zd1211:LinkLEDn = 200
Sep 8 00:48:40 wolvverine kernel: zd1205: (exit)
zd1205_config, /home/users/adi/rpm/BUILD/zd1211-driver-r83/src/zd1205.c
line 2601
Sep 8 00:48:40 wolvverine kernel: zd1205: (exit)
zd1205_init, /home/users/adi/rpm/BUILD/zd1211-driver-r83/src/zd1205.c
line 8570
...
Sep 8 01:50:04 wolvverine kernel: zd1211:Switch to AP mode
Sep 8 01:50:04 wolvverine kernel: zd1211:Pure B-Mode
Sep 8 01:50:04 wolvverine kernel: Mode: AP_BSS
Sep 8 01:50:04 wolvverine kernel: Mode: AP_BSS
Sep 8 01:50:04 wolvverine kernel: zd1205: (enter)
zd1205_open, /home/users/adi/rpm/BUILD/zd1211-driver-r83/src/zd1205.c
line 4353
Sep 8 01:50:04 wolvverine kernel: Mode: AP_BSS
Sep 8 01:50:04 wolvverine kernel: Mode: AP_BSS
Sep 8 01:50:04 wolvverine kernel: zd1205: (exit)
zd1205_open, /home/users/adi/rpm/BUILD/zd1211-driver-r83/src/zd1205.c
line 4436
Sep 8 01:50:08 wolvverine kernel: Re_Asoc: aid=1
Sep 8 01:50:08 wolvverine kernel: Increment mNumBOnlySta
Sep 8 01:50:08 wolvverine kernel: zd1211:STA_ASSOCIATED with
00:13:02:xx:xx:xx
z WEP:
Sep 8 01:40:05 wolvverine kernel: zd1211:Switch to AP mode
Sep 8 01:40:05 wolvverine kernel: zd1211:Pure B-Mode
Sep 8 01:40:05 wolvverine kernel: Mode: AP_BSS
Sep 8 01:40:05 wolvverine kernel: Mode: AP_BSS
Sep 8 01:40:05 wolvverine kernel: keybuf data [12]:
Sep 8 01:40:05 wolvverine kernel: 31 38 30 35 31 39 37 37 31 34 33 30
Sep 8 01:40:05 wolvverine kernel: zd1211:WEP128 Mode
Sep 8 01:40:05 wolvverine kernel: Just Update WEP key
Sep 8 01:40:05 wolvverine kernel: Mode: AP_BSS
Sep 8 01:40:05 wolvverine kernel: zd1205: (enter)
zd1205_open, /home/users/adi/rpm/BUILD/zd1211-driver-r83/src/zd1205.c
line 4353
Sep 8 01:40:05 wolvverine kernel: Mode: AP_BSS
Sep 8 01:40:05 wolvverine kernel: Beacon Interval not match
Sep 8 01:40:05 wolvverine kernel: Mode: AP_BSS
Sep 8 01:40:05 wolvverine kernel: zd1205: (exit)
zd1205_open, /home/users/adi/rpm/BUILD/zd1211-driver-r83/src/zd1205.c
line 4436
[adi w wolvv-lap ~]$ sudo iwlist wlan0 scan
wlan0 Scan completed :
Cell 01 - Address: 00:60:B3:xx:xx:xx
ESSID:"34532454565433456889"
Protocol:IEEE 802.11b
Mode:Master
Channel:6
Encryption key:on
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s
Quality=92/100 Signal level=-38 dBm Noise
level=-38 dBm
Extra: Last beacon: 796ms ago
na laptopie:
[adi w wolvv-lap ~]$ sudo iwconfig wlan0
wlan0 IEEE 802.11b ESSID:"34532454565433456889"
Nickname:"wolvvnet"
Mode:Managed Frequency:2.437 GHz Access Point:
00:60:B3:55:xx:xx:xx
Bit Rate:11 Mb/s Tx-Power:15 dBm
Retry limit:15 RTS thr:off Fragment thr:off
Encryption key:3138-3035-3139-3737-3134-3330-00 Security
mode:open
Power Management:off
Link Quality=92/100 Signal level=-41 dBm Noise level=-42 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:228 Missed beacon:0
Sep 6 04:42:57 wolvv-lap kernel: ieee80211_crypt: registered algorithm
'WEP'
Sep 8 02:02:15 wolvv-lap kernel: ADDRCONF(NETDEV_UP): wlan0: link is
not ready
--
Michał Panasiewicz Linux user nr. #425323 - jabber: wolvverine [ at ] chrome [ dot ] pl || e-mail: wolvverine [ at ] tlen [ dot ] pl , wolvverine [ at ] pld-linux [ dot ] org
http://www.linkomp.pl - Linkomp - Usługi informatyczne dla firm - biuro [ at ] linkomp [ dot ] pl
Więcej informacji o liście dyskusyjnej pld-users-pl