przesiadka na sata

[Mieszko Kaczmarczyk]

Saturday 10 of May 2008 12:15:53 Sylwester Gruszka napisał(a):
> U mnie nie ma "Kernel driver in use:", myślałem, że przez to, że nie
> ma żadnego drivera załadowanego do ata ale w sumie w sata też nie
> pokazuje. lspci -vv też nie pokazuje, nie wiem o co chodzi ;P



To może powinieneś dopisać ponieważ przykładowo u mnie jest:
00:01.1 SMBus: nVidia Corporation MCP61 SMBus (rev a2)
        Subsystem: Giga-byte Technology Unknown device 0c11
        Flags: 66MHz, fast devsel, IRQ 11
        I/O ports at b800 [size=64]
        I/O ports at 1c00 [size=64]
        I/O ports at 1c40 [size=64]
        Capabilities: [44] Power Management version 2
        Kernel driver in use: nForce2_smbus
        Kernel modules: i2c-nforce2


00:06.0 IDE interface: nVidia Corporation MCP61 IDE (rev a2) (prog-if 8a 
[Master SecP PriP])
        Subsystem: Giga-byte Technology Unknown device 5002
        Flags: bus master, 66MHz, fast devsel, latency 0
        [virtual] Memory at 000001f0 (32-bit, non-prefetchable) 
[disabled] [size=8]
        [virtual] Memory at 000003f0 (type 3, non-prefetchable) 
[disabled] [size=1]
        [virtual] Memory at 00000170 (32-bit, non-prefetchable) 
[disabled] [size=8]
        [virtual] Memory at 00000370 (type 3, non-prefetchable) 
[disabled] [size=1]
        I/O ports at f000 [size=16]
        Capabilities: [44] Power Management version 2
        Kernel driver in use: AMD_IDE
        Kernel modules: pata_acpi, ata_generic, pata_amd, amd74xx, 
generic






00:08.0 IDE interface: nVidia Corporation MCP61 SATA Controller (rev a2) 
(prog-if 85 [Master SecO PriO])
        Subsystem: Giga-byte Technology Unknown device b002
        Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21
        I/O ports at 09f0 [size=8]
        I/O ports at 0bf0 [size=4]
        I/O ports at 0970 [size=8]
        I/O ports at 0b70 [size=4]
        I/O ports at d000 [size=16]
        Memory at e5204000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [44] Power Management version 2
        Capabilities: [b0] Message Signalled Interrupts: Mask- 64bit+ 
Queue=0/2 Enable-
        Capabilities: [cc] HyperTransport: MSI Mapping Enable- Fixed+
        Kernel driver in use: sata_nv
        Kernel modules: pata_acpi, ata_generic, sata_nv, generic



00:08.1 IDE interface: nVidia Corporation MCP61 SATA Controller (rev a2) 
(prog-if 85 [Master SecO PriO])
        Subsystem: Giga-byte Technology Unknown device b002
        Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 20
        I/O ports at 09e0 [size=8]
        I/O ports at 0be0 [size=4]
        I/O ports at 0960 [size=8]
        I/O ports at 0b60 [size=4]
        I/O ports at e400 [size=16]
        Memory at e5200000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [44] Power Management version 2
        Capabilities: [b0] Message Signalled Interrupts: Mask- 64bit+ 
Queue=0/2 Enable-
        Capabilities: [cc] HyperTransport: MSI Mapping Enable- Fixed+
        Kernel driver in use: sata_nv
        Kernel modules: pata_acpi, ata_generic, sata_nv, generic


więc wg mnie - brakuje Ci modułów - moze załaduj je ręcznie przez 
modprobe zanim dopiszesz na stałe?


Powodzenia
Miesiu
-- 
Zobacz cyfrową stację pogody:
http://miesiu.republika.pl/stacja_pogody/stacja_pogody.html









.