mdassemble v. 3.1-1 uruchomiony z initrd nie wykrywa /dev/md0 - system nie wstaje
Bartosz Lis
bartoszl w ics.p.lodz.pl
Śro, 25 Lis 2009, 13:01:53 CET
Dnia wtorek, 24 listopada 2009 o 21:04:51 Arkadiusz Miskiewicz napisał(a):
> On Tuesday 24 of November 2009, Bartosz Lis wrote:
> > Witam,
> >
> > Po ostatnim upgrade th, w którym zainstalowało mi się
> > mdadm-initrd-3.1-1.x86_64
> > oraz po regeneracji initrd system przestał wstawać. Poniżej komunikaty
> > złapane na porcie szeregowym:
>
> Dorzuć debuginitrd przy startowaniu jajka.
>
Witam,
Poniżej komunikaty z włączonym debuginitrd począwszy od załadowania scsi_mod.
Pozdrawiam,
--
Bartosz Lis @ Inst. of Information Technology, Technical Univ. of Lodz, Poland
bartoszl @ ics.p.lodz.pl
----8<----
+ insmod /lib/modules/2.6.31.5-1/kernel/drivers/scsi/scsi_mod.ko
[ 5.906050] SCSI subsystem initialized
+ insmod /lib/modules/2.6.31.5-1/kernel/drivers/ata/libata.ko
+ insmod /lib/modules/2.6.31.5-1/kernel/drivers/[ 5.930656] ahci
0000:00:1f.9
ata/ahci.ko
[ 5.937643] ahci: SSS flag set, parallel bus scan disabled
[ 5.944139] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f
ie
[ 5.952299] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio
slu
[ 5.989046] scsi0 : ahci
[ 5.991859] scsi1 : ahci
[ 5.994520] scsi2 : ahci
[ 5.997192] scsi3 : ahci
[ 5.999843] scsi4 : ahci
[ 6.002508] scsi5 : ahci
[ 6.005229] ata1: SATA max UDMA/133 abar m2048 w 0xfabd6000 port 0xfabd6100
ir0
[ 6.012607] ata2: SATA max UDMA/133 abar m2048 w 0xfabd6000 port 0xfabd6180
ir0
[ 6.019986] ata3: SATA max UDMA/133 abar m2048 w 0xfabd6000 port 0xfabd6200
ir0
[ 6.027367] ata4: SATA max UDMA/133 abar m2048 w 0xfabd6000 port 0xfabd6280
ir0
[ 6.034748] ata5: SATA max UDMA/133 abar m2048 w 0xfabd6000 port 0xfabd6300
ir0
[ 6.042128] ata6: SATA max UDMA/133 abar m2048 w 0xfabd6000 port 0xfabd6380
ir0
[ 6.368446] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 6.418988] ata1.00: ATA-7: ST3500630NS, 3.AEK, max UDMA/133
[ 6.424639] ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 6.477206] ata1.00: configured for UDMA/133
[ 6.491708] scsi 0:0:0:0: Direct-Access ATA ST3500630NS 3.AE
P5
[ 7.217192] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 7.270233] ata2.00: ATA-7: ST3500630NS, 3.AEK, max UDMA/133
[ 7.275888] ata2.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 7.328453] ata2.00: configured for UDMA/133
[ 7.343753] scsi 1:0:0:0: Direct-Access ATA ST3500630NS 3.AE
P5
[ 8.069268] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 8.076127] ata3.00: ATA-8: WDC WD1002FBYS-02A6B0, 03.00C06, max UDMA/133
[ 8.082905] ata3.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 8.091397] ata3.00: configured for UDMA/133
[ 8.105939] scsi 2:0:0:0: Direct-Access ATA WDC WD1002FBYS-0 03.0
P5
[ 8.432066] ata4: SATA link down (SStatus 0 SControl 300)
[ 9.327410] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 9.347509] ata5.00: ATAPI: DV-28E-V, 1.AB, max UDMA/33
[ 9.387417] ata5.00: configured for UDMA/33
[ 9.470353] scsi 4:0:0:0: CD-ROM TEAC DV-28E-V 1.AB
P5
[ 9.796720] ata6: SATA link down (SStatus 0 SControl 300)
+ insmod /lib/modules/2.6.31.5-1/kernel/drivers/md/md-mod.ko
+ insmod /lib/modules/2.6.31.5-1[ 9.821085] md: raid1 personality
registered1
/kernel/drivers/md/raid1.ko
+ insmod /lib/modules/2.6.31.5-1/ke[ 9.831307] sd 0:0:0:0: [sda] 976773168
5)
[ 9.836724] sd 1:0:0:0: [sdb] 976773168 512-byte logical blocks: (500
GB/465)
[ 9.836753] sd 1:0:0:0: [sdb] Write Protect is off
[ 9.836772] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled,
doeA
[ 9.836863] sdb:
[ 9.840056] sd 2:0:0:0: [sdc] 1953525168 512-byte logical blocks: (1.00
TB/9)
[ 9.840085] sd 2:0:0:0: [sdc] Write Protect is off
[ 9.840102] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled,
doeA
[ 9.840201] sdc: sdc1 sdc2 sdc3 sdc4
rnel/lib/crc-t10[ 9.888144] sdb1
[ 9.888173] sd 0:0:0:0: [sda] Write Protect is off
[ 9.888192] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doeA
[ 9.905266] sdb2dif.ko
+ insmod sdb3 sdb4
/lib/modules/2.[ 9.909686] sda:
[ 9.909976] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 9.910023] sd 2:0:0:0: [sdc] Attached SCSI disk
6.31.5-1/kernel/drivers/scsi/sd_mod.ko
[ 9.942985] sda1 sda2 sda3 sda4
[ 9.946696] sd 0:0:0:0: [sda] Attached SCSI disk
+ insmod /lib/modules/2.6.31.5-1/kernel/drivers/scsi/scsi_wait_scan.ko
+ rmmod scsi_wait_scan
+ insmod /lib/modules/2.6.31.5-1/kernel/fs/mbcache.ko
+ insmod /lib/modules/2.6.31.5-1/kernel/fs/jbd/jbd.ko
+ insmod /lib/modules/2.6.31.5-1/kernel/fs/ext3/ext3.ko
+ mdassemble
mdadm: unexpected failure opening /dev/md0
+ [ 0900 != 0900 ]
+ : Last shell before umounting all and giving control over to real init.
+ debugshell
+ :
+ umount /proc
[ 10.040031] VFS: Cannot open root device "0900" or unknown-block(9,0)
[ 10.046460] Please append a correct "root=" boot option; here are the
availa:
[ 10.054795] 0810 488386584 sdb driver: sd
[ 10.059341] 0811 88326 sdb1
[ 10.063198] 0812 4064445 sdb2
[ 10.067058] 0813 4064445 sdb3
[ 10.070916] 0814 480166785 sdb4
[ 10.074775] 0820 976762584 sdc driver: sd
[ 10.079327] 0821 88326 sdc1
[ 10.083184] 0822 4064445 sdc2
[ 10.087036] 0823 4064445 sdc3
[ 10.090894] 0824 968542785 sdc4
[ 10.094746] 0800 488386584 sda driver: sd
[ 10.099297] 0801 88326 sda1
[ 10.103154] 0802 4064445 sda2
[ 10.107006] 0803 4064445 sda3
[ 10.110865] 0804 480166785 sda4
[ 10.114725] Kernel panic - not syncing: VFS: Unable to mount root fs on
unkn)
[ 10.122973] Pid: 1, comm: swapper xid: #0 Tainted: G M 2.6.31.5-1
#1
[ 10.130005] Call Trace:
[ 10.132456] [<ffffffff814698e3>] panic+0x82/0x134
[ 10.137243] [<ffffffff816df00d>] mount_block_root+0x1ea/0x29e
[ 10.143063] [<ffffffff816df126>] mount_root+0x65/0x80
[ 10.148193] [<ffffffff816dfe56>] initrd_load+0x25b/0x371
[ 10.153584] [<ffffffff816df22b>] prepare_namespace+0xea/0x1ca
[ 10.159409] [<ffffffff816de3a1>] kernel_init+0x1bb/0x1e7
[ 10.164799] [<ffffffff810042da>] child_rip+0xa/0x20
[ 10.169758] [<ffffffff816de1e6>] ? kernel_init+0x0/0x1e7
[ 10.175147] [<ffffffff810042d0>] ? child_rip+0x0/0x20
----8<----
Więcej informacji o liście dyskusyjnej pld-users-pl