mdamd problem

lord_Niedzwiedz sir_Misiek w o2.pl
Śro, 4 Lis 2015, 13:28:51 CET


>>>>> SMART pokazuje że oba dyski zdrowe ?
>>>> A jak to sprawdzić ?
>>> smartctl -a /dev/sd?
>>       Wywalił mi 5 stron A4.
> Może pokaż?
>
>> Czego szukać ?  ;-]
> FAILING NOW przy własnościach ;)
>
Proszę  ;-)

[root w dns2 ~]# smartctl -a /dev/sdb
smartctl 6.3 2014-07-26 r3976 [i686-linux-4.2.3-1] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Constellation ES.3
Device Model:     ST1000NM0033-9ZM173
Serial Number:    Z1W4LR7G
LU WWN Device Id: 5 000c50 0873b1bab
Firmware Version: SN04
User Capacity:    1,000,204,886,016 bytes [1,00 TB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    7200 rpm
Form Factor:      3.5 inches
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ACS-2 (minor revision not indicated)
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 1.5 Gb/s)
Local Time is:    Wed Nov  4 13:28:13 2015 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
  ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
SMART Status not supported: Invalid ATA output register values
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.

General SMART Values:
Offline data collection status:  (0x82)    Offline data collection activity
                     was completed without error.
                     Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0)    The previous self-test 
routine completed
                     without error or no self-test has ever
                     been run.
Total time to complete Offline
data collection:         (  592) seconds.
Offline data collection
capabilities:              (0x7b) SMART execute Offline immediate.
                     Auto Offline data collection on/off support.
                     Suspend Offline collection upon new
                     command.
                     Offline surface scan supported.
                     Self-test supported.
                     Conveyance Self-test supported.
                     Selective Self-test supported.
SMART capabilities:            (0x0003)    Saves SMART data before entering
                     power-saving mode.
                     Supports SMART auto save timer.
Error logging capability:        (0x01)    Error logging supported.
                     General Purpose Logging supported.
Short self-test routine
recommended polling time:      (   1) minutes.
Extended self-test routine
recommended polling time:      ( 115) minutes.
Conveyance self-test routine
recommended polling time:      (   2) minutes.
SCT capabilities:            (0x50bd)    SCT Status supported.
                     SCT Error Recovery Control supported.
                     SCT Feature Control supported.
                     SCT Data Table supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE UPDATED  
WHEN_FAILED RAW_VALUE
   1 Raw_Read_Error_Rate     0x000f   080   063   044    Pre-fail 
Always       -       116858893
   3 Spin_Up_Time            0x0003   098   098   000    Pre-fail 
Always       -       0
   4 Start_Stop_Count        0x0032   100   100   020    Old_age 
Always       -       6
   5 Reallocated_Sector_Ct   0x0033   100   100   010    Pre-fail 
Always       -       0
   7 Seek_Error_Rate         0x000f   070   060   030    Pre-fail 
Always       -       12572406
   9 Power_On_Hours          0x0032   100   100   000    Old_age 
Always       -       626
  10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail 
Always       -       0
  12 Power_Cycle_Count       0x0032   100   100   020    Old_age 
Always       -       6
184 End-to-End_Error        0x0032   100   100   099    Old_age 
Always       -       0
187 Reported_Uncorrect      0x0032   100   100   000    Old_age 
Always       -       0
188 Command_Timeout         0x0032   100   100   000    Old_age 
Always       -       0
189 High_Fly_Writes         0x003a   100   100   000    Old_age 
Always       -       0
190 Airflow_Temperature_Cel 0x0022   074   071   045    Old_age 
Always       -       26 (Min/Max 20/28)
191 G-Sense_Error_Rate      0x0032   100   100   000    Old_age 
Always       -       0
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age 
Always       -       5
193 Load_Cycle_Count        0x0032   100   100   000    Old_age 
Always       -       31
194 Temperature_Celsius     0x0022   026   040   000    Old_age 
Always       -       26 (0 20 0 0 0)
195 Hardware_ECC_Recovered  0x001a   050   011   000    Old_age 
Always       -       116858893
197 Current_Pending_Sector  0x0012   100   100   000    Old_age 
Always       -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age 
Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age 
Always       -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
  SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
     1        0        0  Not_testing
     2        0        0  Not_testing
     3        0        0  Not_testing
     4        0        0  Not_testing
     5        0        0  Not_testing
Selective self-test flags (0x0):
   After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.



Więcej informacji o liście pld-users-pl