smart komunikat - problem 3
lord_Niedzwiedz
sir_Misiek w o2.pl
Pią, 27 Lis 2015, 14:27:03 CET
Idąc tym tropem po sprawdzałem sobie dyski w macierzach.
Tych komunikatów też nie rozumiem.
-bash-4.3# smartctl -a /dev/sda
smartctl 6.4 2015-06-04 r4109 [x86_64-linux-3.14.10-1] (local build)
Copyright (C) 2002-15, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Hitachi Deskstar 7K3000
Device Model: Hitachi HDS723030ALA640
Serial Number: MK0311YHG5DK6A
LU WWN Device Id: 5 000cca 225c274fc
Firmware Version: MKAOA580
User Capacity: 3,000,592,982,016 bytes [3,00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Fri Nov 27 14:28:47 2015 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x85) Offline data collection activity
was aborted by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 249) Self-test routine in progress...
90% of test remaining.
Total time to complete Offline
data collection: (26895) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 449) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail
Always - 0
2 Throughput_Performance 0x0005 136 136 054 Pre-fail
Offline - 80
3 Spin_Up_Time 0x0007 140 140 024 Pre-fail
Always - 501 (Average 605)
4 Start_Stop_Count 0x0012 100 100 000 Old_age
Always - 60
5 Reallocated_Sector_Ct 0x0033 046 046 005 Pre-fail
Always - 1139
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail
Always - 0
8 Seek_Time_Performance 0x0005 135 135 020 Pre-fail
Offline - 26
9 Power_On_Hours 0x0012 095 095 000 Old_age
Always - 41410
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail
Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age
Always - 60
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age
Always - 106
193 Load_Cycle_Count 0x0012 100 100 000 Old_age
Always - 106
194 Temperature_Celsius 0x0002 214 214 000 Old_age
Always - 28 (Min/Max 21/46)
196 Reallocated_Event_Count 0x0032 044 044 000 Old_age
Always - 1183
197 Current_Pending_Sector 0x0022 100 100 000 Old_age
Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age
Always - 0
SMART Error Log Version: 1
ATA Error Count: 127 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 127 occurred at disk power-on lifetime: 40967 hours (1706 days +
23 hours)
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 10 c8 e6 b9 05 Error: WP at LBA = 0x05b9e6c8 = 96069320
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 28 78 46 10 72 40 08 3d+03:08:06.197 WRITE FPDMA QUEUED
60 08 70 e6 3a cf 40 08 3d+03:08:06.197 READ FPDMA QUEUED
60 10 68 c8 e6 b9 40 08 3d+03:08:06.197 READ FPDMA QUEUED
61 08 60 88 f3 b6 40 08 3d+03:08:06.197 WRITE FPDMA QUEUED
61 08 58 be 9a e5 40 08 3d+03:08:06.197 WRITE FPDMA QUEUED
Error 126 occurred at disk power-on lifetime: 40966 hours (1706 days +
22 hours)
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 10 c8 e6 b9 05 Error: UNC at LBA = 0x05b9e6c8 = 96069320
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 10 e8 c8 e6 b9 40 08 3d+03:08:02.881 READ FPDMA QUEUED
60 10 e0 18 e6 b9 40 08 3d+03:08:02.880 READ FPDMA QUEUED
60 10 d8 18 da b9 40 08 3d+03:08:02.855 READ FPDMA QUEUED
60 10 d0 f8 d8 b9 40 08 3d+03:08:02.849 READ FPDMA QUEUED
ea 00 00 00 00 00 a0 08 3d+03:08:02.776 FLUSH CACHE EXT
Error 125 occurred at disk power-on lifetime: 40784 hours (1699 days + 8
hours)
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 7b d5 6a 36 04 Error: UNC at LBA = 0x04366ad5 = 70675157
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 80 28 d0 6a 36 40 08 1d+16:32:08.845 READ FPDMA QUEUED
61 02 20 c6 32 0f 40 08 1d+16:32:08.844 WRITE FPDMA QUEUED
ea 00 00 00 00 00 a0 08 1d+16:32:08.831 FLUSH CACHE EXT
61 02 10 10 f3 f5 40 08 1d+16:32:08.830 WRITE FPDMA QUEUED
ea 00 00 00 00 00 a0 08 1d+16:32:08.820 FLUSH CACHE EXT
Error 124 occurred at disk power-on lifetime: 40784 hours (1699 days + 8
hours)
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 93 d5 6a 36 04 Error: UNC at LBA = 0x04366ad5 = 70675157
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 d0 68 6a 36 40 08 1d+16:32:05.832 READ FPDMA QUEUED
60 00 c8 68 66 36 40 08 1d+16:32:05.828 READ FPDMA QUEUED
60 00 c0 68 62 36 40 08 1d+16:32:05.824 READ FPDMA QUEUED
60 00 b8 68 5e 36 40 08 1d+16:32:05.771 READ FPDMA QUEUED
60 00 b0 68 5a 36 40 08 1d+16:32:05.759 READ FPDMA QUEUED
Error 123 occurred at disk power-on lifetime: 40784 hours (1699 days + 8
hours)
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 80 38 a3 0e 04 Error: UNC at LBA = 0x040ea338 = 68068152
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 d0 70 08 aa 0e 40 08 1d+16:31:38.290 READ FPDMA QUEUED
60 08 68 80 13 3e 40 08 1d+16:31:38.288 READ FPDMA QUEUED
60 50 60 b8 a5 0e 40 08 1d+16:31:38.288 READ FPDMA QUEUED
60 80 58 38 a5 0e 40 08 1d+16:31:38.288 READ FPDMA QUEUED
60 80 50 b8 a4 0e 40 08 1d+16:31:38.288 READ FPDMA QUEUED
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Więcej informacji o liście pld-users-pl