SOURCES (LINUX_2_6): linux-2.6.19-imq1.diff (NEW) - based on 2.6.1...

mguevara mguevara at pld-linux.org
Fri Dec 22 01:51:26 CET 2006


Author: mguevara                     Date: Fri Dec 22 00:51:26 2006 GMT
Module: SOURCES                       Tag: LINUX_2_6
---- Log message:
- based on 2.6.17 patch, some stuff moved from net/sched/sch_generic.c
  to net/core/dev.c for 2.6.19 compatibility. not tested

---- Files affected:
SOURCES:
   linux-2.6.19-imq1.diff (NONE -> 1.1.2.1)  (NEW)

---- Diffs:

================================================================
Index: SOURCES/linux-2.6.19-imq1.diff
diff -u /dev/null SOURCES/linux-2.6.19-imq1.diff:1.1.2.1
--- /dev/null	Fri Dec 22 01:51:26 2006
+++ SOURCES/linux-2.6.19-imq1.diff	Fri Dec 22 01:51:21 2006
@@ -0,0 +1,886 @@
+diff -Nru linux-2.6.17.orig/drivers/net/Kconfig linux-2.6.17/drivers/net/Kconfig
+--- linux-2.6.17.orig/drivers/net/Kconfig	2006-06-18 01:49:35.000000000 +0000
++++ linux-2.6.17/drivers/net/Kconfig	2006-09-06 20:58:51.000000000 +0000
+@@ -93,6 +93,129 @@
+ 	  To compile this driver as a module, choose M here: the module
+ 	  will be called eql.  If unsure, say N.
+ 
++config IMQ
++       tristate "IMQ (intermediate queueing device) support"
++       depends on NETDEVICES && NETFILTER
++       ---help---
++         The IMQ device(s) is used as placeholder for QoS queueing disciplines.
++         Every packet entering/leaving the IP stack can be directed through
++         the IMQ device where it's enqueued/dequeued to the attached qdisc.
++         This allows you to treat network devices as classes and distribute
++         bandwidth among them. Iptables is used to specify through which IMQ
++         device, if any, packets travel.
++
++         More information at: http://www.linuximq.net/
++
++         To compile this driver as a module, choose M here: the module
++         will be called imq.  If unsure, say N.
++
++choice
++        prompt "IMQ behavior (PRE/POSTROUTING)"
++	depends on IMQ
++        default IMQ_BEHAVIOR_BA
++        help
++
++                This settings defines how IMQ behaves in respect to its
++                hooking in PREROUTING and POSTROUTING.
++
++                IMQ can work in any of the following ways:
++
++                    PREROUTING   |      POSTROUTING
++                -----------------|-------------------
++                #1  After NAT    |      After NAT
++                #2  After NAT    |      Before NAT
++                #3  Before NAT   |      After NAT
++                #4  Before NAT   |      Before NAT
++
++                The default behavior is to hook before NAT on PREROUTING
++                and after NAT on POSTROUTING (#3).
++
++                This settings are specially usefull when trying to use IMQ
++                to shape NATed clients.
++
++                More information can be found at: www.linuximq.net
++
++                If not sure leave the default settings alone.
++
++config IMQ_BEHAVIOR_AA
++        bool "IMQ AA"
++        help
++                This settings defines how IMQ behaves in respect to its
++                hooking in PREROUTING and POSTROUTING.
++
++                Choosing this option will make IMQ hook like this:
++
++                PREROUTING:   After NAT
++                POSTROUTING:  After NAT
++
++                More information can be found at: www.linuximq.net
++
++                If not sure leave the default settings alone.
++
++config IMQ_BEHAVIOR_AB
++        bool "IMQ AB"
++        help
++                This settings defines how IMQ behaves in respect to its
++                hooking in PREROUTING and POSTROUTING.
++
++                Choosing this option will make IMQ hook like this:
++
++                PREROUTING:   After NAT
++                POSTROUTING:  Before NAT
++
++                More information can be found at: www.linuximq.net
++
++                If not sure leave the default settings alone.
++
++config IMQ_BEHAVIOR_BA
++        bool "IMQ BA"
++        help
++                This settings defines how IMQ behaves in respect to its
++                hooking in PREROUTING and POSTROUTING.
++
++                Choosing this option will make IMQ hook like this:
++
++                PREROUTING:   Before NAT
++                POSTROUTING:  After NAT
++
++                More information can be found at: www.linuximq.net
++
++                If not sure leave the default settings alone.
++
++config IMQ_BEHAVIOR_BB
++        bool "IMQ BB"
++        help
++                This settings defines how IMQ behaves in respect to its
++                hooking in PREROUTING and POSTROUTING.
++
++                Choosing this option will make IMQ hook like this:
++
++                PREROUTING:   Before NAT
++                POSTROUTING:  Before NAT
++
++                More information can be found at: www.linuximq.net
++
++                If not sure leave the default settings alone.
++
++endchoice
++
++config IMQ_NUM_DEVS
++
++        int "Number of IMQ devices"
++	range 2 8
++	depends on IMQ
++        default "2"
++        help
++
++                This settings defines how many IMQ devices will be 
++		created.
++
++		The default value is 2.
++
++                More information can be found at: www.linuximq.net
++
++                If not sure leave the default settings alone.
++
+ config TUN
+ 	tristate "Universal TUN/TAP device driver support"
+ 	select CRC32
+diff -Nru linux-2.6.17.orig/drivers/net/Makefile linux-2.6.17/drivers/net/Makefile
+--- linux-2.6.17.orig/drivers/net/Makefile	2006-06-18 01:49:35.000000000 +0000
++++ linux-2.6.17/drivers/net/Makefile	2006-09-06 20:58:51.000000000 +0000
+@@ -125,6 +125,7 @@
+ endif
+ 
+ obj-$(CONFIG_DUMMY) += dummy.o
++obj-$(CONFIG_IMQ) += imq.o
+ obj-$(CONFIG_IFB) += ifb.o
+ obj-$(CONFIG_DE600) += de600.o
+ obj-$(CONFIG_DE620) += de620.o
+diff -Nru linux-2.6.17.orig/drivers/net/imq.c linux-2.6.17/drivers/net/imq.c
+--- linux-2.6.17.orig/drivers/net/imq.c	1970-01-01 00:00:00.000000000 +0000
++++ linux-2.6.17/drivers/net/imq.c	2006-09-06 20:58:51.000000000 +0000
+@@ -0,0 +1,403 @@
++/*
++ *             Pseudo-driver for the intermediate queue device.
++ *
++ *             This program is free software; you can redistribute it and/or
++ *             modify it under the terms of the GNU General Public License
++ *             as published by the Free Software Foundation; either version
++ *             2 of the License, or (at your option) any later version.
++ *
++ * Authors:    Patrick McHardy, <kaber at trash.net>
++ *
++ *            The first version was written by Martin Devera, <devik at cdi.cz>
++ *
++ * Credits:    Jan Rafaj <imq2t at cedric.vabo.cz>
++ *              - Update patch to 2.4.21
++ *             Sebastian Strollo <sstrollo at nortelnetworks.com>
++ *              - Fix "Dead-loop on netdevice imq"-issue
++ *             Marcel Sebek <sebek64 at post.cz>
++ *              - Update to 2.6.2-rc1
++ *
++ *	       After some time of inactivity there is a group taking care
++ *	       of IMQ again: http://www.linuximq.net
++ *
++ *
++ *	       2004/06/30 - New version of IMQ patch to kernels <=2.6.7 including
++ *	       the following changes:
++ *
++ *	       - Correction of ipv6 support "+"s issue (Hasso Tepper)
++ *	       - Correction of imq_init_devs() issue that resulted in 
++ *	       kernel OOPS unloading IMQ as module (Norbert Buchmuller)
++ *	       - Addition of functionality to choose number of IMQ devices
++ *	       during kernel config (Andre Correa)
++ *	       - Addition of functionality to choose how IMQ hooks on 
++ *	       PRE and POSTROUTING (after or before NAT) (Andre Correa)
++ *	       - Cosmetic corrections (Norbert Buchmuller) (Andre Correa)
++ *
++ *
++ *             2005/12/16 - IMQ versions between 2.6.7 and 2.6.13 were 
++ *             released with almost no problems. 2.6.14-x was released 
++ *             with some important changes: nfcache was removed; After 
++ *             some weeks of trouble we figured out that some IMQ fields 
++ *             in skb were missing in skbuff.c - skb_clone and copy_skb_header.
++ *             These functions are correctly patched by this new patch version.
++ *
++ *             Thanks for all who helped to figure out all the problems with 
++ *             2.6.14.x: Patrick McHardy, Rune Kock, VeNoMouS, Max CtRiX,
++ *             Kevin Shanahan, Richard Lucassen, Valery Dachev (hopefully 
++ *             I didn't forget anybody). I apologize again for my lack of time.
++ *
++ *             More info at: http://www.linuximq.net/ (Andre Correa)
++ */
++
++#include <linux/config.h>
++#include <linux/module.h>
++#include <linux/kernel.h>
++#include <linux/moduleparam.h>
++#include <linux/skbuff.h>
++#include <linux/netdevice.h>
++#include <linux/rtnetlink.h>
++#include <linux/if_arp.h>
++#include <linux/netfilter.h>
++#include <linux/netfilter_ipv4.h>
++#if defined(CONFIG_IPV6) || defined (CONFIG_IPV6_MODULE)
++	#include <linux/netfilter_ipv6.h>
++#endif
++#include <linux/imq.h>
++#include <net/pkt_sched.h>
++
++static nf_hookfn imq_nf_hook;
++
++static struct nf_hook_ops imq_ingress_ipv4 = {
++       .hook           = imq_nf_hook,
++       .owner          = THIS_MODULE,
++       .pf             = PF_INET,
++       .hooknum        = NF_IP_PRE_ROUTING,
++#if defined(CONFIG_IMQ_BEHAVIOR_BA) || defined(CONFIG_IMQ_BEHAVIOR_BB)
++       .priority       = NF_IP_PRI_MANGLE + 1
++#else
++       .priority       = NF_IP_PRI_NAT_DST + 1
++#endif
++};
++
++static struct nf_hook_ops imq_egress_ipv4 = {
++       .hook           = imq_nf_hook,
++       .owner          = THIS_MODULE,
++       .pf             = PF_INET,
++       .hooknum        = NF_IP_POST_ROUTING,
++#if defined(CONFIG_IMQ_BEHAVIOR_AA) || defined(CONFIG_IMQ_BEHAVIOR_BA)
++       .priority       = NF_IP_PRI_LAST
++#else
++       .priority       = NF_IP_PRI_NAT_SRC - 1
++#endif
++};
++
++#if defined(CONFIG_IPV6) || defined (CONFIG_IPV6_MODULE)
++static struct nf_hook_ops imq_ingress_ipv6 = {
++       .hook           = imq_nf_hook,
++       .owner          = THIS_MODULE,
++       .pf             = PF_INET6,
++       .hooknum        = NF_IP6_PRE_ROUTING,
++#if defined(CONFIG_IMQ_BEHAVIOR_BA) || defined(CONFIG_IMQ_BEHAVIOR_BB)
++       .priority       = NF_IP6_PRI_MANGLE + 1
++#else
++       .priority       = NF_IP6_PRI_NAT_DST + 1
++#endif
++};
++
++static struct nf_hook_ops imq_egress_ipv6 = {
++       .hook           = imq_nf_hook,
++       .owner          = THIS_MODULE,
++       .pf             = PF_INET6,
++       .hooknum        = NF_IP6_POST_ROUTING,
++#if defined(CONFIG_IMQ_BEHAVIOR_AA) || defined(CONFIG_IMQ_BEHAVIOR_BA)
++       .priority       = NF_IP6_PRI_LAST
++#else
++       .priority       = NF_IP6_PRI_NAT_SRC - 1
++#endif
++};
++#endif
++
++#if defined(CONFIG_IMQ_NUM_DEVS)
++static unsigned int numdevs = CONFIG_IMQ_NUM_DEVS;
++#else
++static unsigned int numdevs = 2;
++#endif
++
++static struct net_device *imq_devs;
++
++static struct net_device_stats *imq_get_stats(struct net_device *dev)
++{
++       return (struct net_device_stats *)dev->priv;
++}
++
++/* called for packets kfree'd in qdiscs at places other than enqueue */
++static void imq_skb_destructor(struct sk_buff *skb)
++{
++       struct nf_info *info = skb->nf_info;
++
++       if (info) {
++               if (info->indev)
++                       dev_put(info->indev);
++               if (info->outdev)
++                       dev_put(info->outdev);
++               kfree(info);
++       }
++}
++
++static int imq_dev_xmit(struct sk_buff *skb, struct net_device *dev)
++{
++       struct net_device_stats *stats = (struct net_device_stats*) dev->priv;
++
++       stats->tx_bytes += skb->len;
++       stats->tx_packets++;
++
++       skb->imq_flags = 0;
++       skb->destructor = NULL;
++
++       dev->trans_start = jiffies;
++       nf_reinject(skb, skb->nf_info, NF_ACCEPT);
++       return 0;
++}
++
++static int imq_nf_queue(struct sk_buff *skb, struct nf_info *info, unsigned queue_num, void *data)
++{
++       struct net_device *dev;
++       struct net_device_stats *stats;
++       struct sk_buff *skb2 = NULL;
++       struct Qdisc *q;
++       unsigned int index = skb->imq_flags&IMQ_F_IFMASK;
++       int ret = -1;
++
++       if (index > numdevs) 
++               return -1;
++
++       dev = imq_devs + index;
++       if (!(dev->flags & IFF_UP)) {
++               skb->imq_flags = 0;
++               nf_reinject(skb, info, NF_ACCEPT);
++               return 0;
++       }
++       dev->last_rx = jiffies;
++
++       if (skb->destructor) {
++               skb2 = skb;
++               skb = skb_clone(skb, GFP_ATOMIC);
++               if (!skb)
++                       return -1;
++       }
++       skb->nf_info = info;
++
++       stats = (struct net_device_stats *)dev->priv;
++       stats->rx_bytes+= skb->len;
++       stats->rx_packets++;
++
++       spin_lock_bh(&dev->queue_lock);
++       q = dev->qdisc;
++       if (q->enqueue) {
++               q->enqueue(skb_get(skb), q);
++               if (skb_shared(skb)) {
++                       skb->destructor = imq_skb_destructor;
++                       kfree_skb(skb);
++                       ret = 0;
++               }
++       }
++       if (spin_is_locked(&dev->xmit_lock))
++               netif_schedule(dev);
++       else
++
++        while (!netif_queue_stopped(dev) &&
++               qdisc_restart(dev)<0)
++                /* NOTHING */;
++
++       spin_unlock_bh(&dev->queue_lock);
++
++       if (skb2)
++               kfree_skb(ret ? skb : skb2);
++
++       return ret;
++}
++
++static struct nf_queue_handler nfqh = {
++       .name  = "imq",
++       .outfn = imq_nf_queue,
++};
++
++static unsigned int imq_nf_hook(unsigned int hook, struct sk_buff **pskb,
++                  const struct net_device *indev,
++                  const struct net_device *outdev,
++                  int (*okfn)(struct sk_buff *))
++{
++       if ((*pskb)->imq_flags & IMQ_F_ENQUEUE)
++               return NF_QUEUE;
++
++       return NF_ACCEPT;
++}
++
++
++static int __init imq_init_hooks(void)
++{
++       int err;
++
++       err = nf_register_queue_handler(PF_INET, &nfqh);
++       if (err > 0)
++               goto err1;
++       if ((err = nf_register_hook(&imq_ingress_ipv4)))
++               goto err2;
++       if ((err = nf_register_hook(&imq_egress_ipv4)))
++               goto err3;
++#if defined(CONFIG_IPV6) || defined (CONFIG_IPV6_MODULE)
++       if ((err = nf_register_queue_handler(PF_INET6, &nfqh)))
++               goto err4;
++       if ((err = nf_register_hook(&imq_ingress_ipv6)))
++               goto err5;
++       if ((err = nf_register_hook(&imq_egress_ipv6)))
++               goto err6;
++#endif
++
++       return 0;
++
++#if defined(CONFIG_IPV6) || defined (CONFIG_IPV6_MODULE)
++err6:
++       nf_unregister_hook(&imq_ingress_ipv6);
++err5:
++       nf_unregister_queue_handler(PF_INET6);
++err4:
++       nf_unregister_hook(&imq_egress_ipv6);
++#endif
++err3:
++       nf_unregister_hook(&imq_ingress_ipv4);
++err2:
++       nf_unregister_queue_handler(PF_INET);
++err1:
++       return err;
++}
++
++static void __exit imq_unhook(void)
++{
++       nf_unregister_hook(&imq_ingress_ipv4);
++       nf_unregister_hook(&imq_egress_ipv4);
++       nf_unregister_queue_handler(PF_INET);
++#if defined(CONFIG_IPV6) || defined (CONFIG_IPV6_MODULE)
++       nf_unregister_hook(&imq_ingress_ipv6);
++       nf_unregister_hook(&imq_egress_ipv6);
++       nf_unregister_queue_handler(PF_INET6);
++#endif
++}
++
++static int __init imq_dev_init(struct net_device *dev)
++{
++       dev->hard_start_xmit    = imq_dev_xmit;
++       dev->type               = ARPHRD_VOID;
++       dev->mtu                = 1500;
++       dev->tx_queue_len       = 30;
++       dev->flags              = IFF_NOARP;
++       dev->priv = kmalloc(sizeof(struct net_device_stats), GFP_KERNEL);
++       if (dev->priv == NULL)
++               return -ENOMEM;
++       memset(dev->priv, 0, sizeof(struct net_device_stats));
++       dev->get_stats          = imq_get_stats;
++
++       return 0;
++}
++
++static void imq_dev_uninit(struct net_device *dev)
++{
++       kfree(dev->priv);
++}
++
++static int __init imq_init_devs(void)
++{
++       struct net_device *dev;
++       int i,j;
++       j = numdevs;
++
++       if (!numdevs || numdevs > IMQ_MAX_DEVS) {
++               printk(KERN_ERR "IMQ: numdevs has to be betweed 1 and %u\n",
++                      IMQ_MAX_DEVS);
++               return -EINVAL;
++       }
++
++       imq_devs = kmalloc(sizeof(struct net_device) * numdevs, GFP_KERNEL);
++       if (!imq_devs)
++               return -ENOMEM;
++       memset(imq_devs, 0, sizeof(struct net_device) * numdevs);
++
++       /* we start counting at zero */
++       numdevs--;
++
++       for (i = 0, dev = imq_devs; i <= numdevs; i++, dev++) {
++               SET_MODULE_OWNER(dev);
++               strcpy(dev->name, "imq%d");
++               dev->init   = imq_dev_init;
++               dev->uninit = imq_dev_uninit;
++
++               if (register_netdev(dev) < 0)
++                       goto err_register;
++       }
++       printk(KERN_INFO "IMQ starting with %u devices...\n", j);
++       return 0;
++
++err_register:
++       for (; i; i--)
++               unregister_netdev(--dev);
++       kfree(imq_devs);
++       return -EIO;
++}
++
++static void imq_cleanup_devs(void)
++{
++       int i;
++       struct net_device *dev = imq_devs;
++
++       for (i = 0; i <= numdevs; i++)
++               unregister_netdev(dev++);
++
++       kfree(imq_devs);
++}
++
++static int __init imq_init_module(void)
++{
++       int err;
++
++       if ((err = imq_init_devs())) {
++               printk(KERN_ERR "IMQ: Error trying imq_init_devs()\n");
++               return err;
++       }
++       if ((err = imq_init_hooks())) {
++               printk(KERN_ERR "IMQ: Error trying imq_init_hooks()\n");
++               imq_cleanup_devs();
++               return err;
++       }
++
++       printk(KERN_INFO "IMQ driver loaded successfully.\n");
++
++#if defined(CONFIG_IMQ_BEHAVIOR_BA) || defined(CONFIG_IMQ_BEHAVIOR_BB)
++       printk(KERN_INFO "\tHooking IMQ before NAT on PREROUTING.\n");
++#else
++       printk(KERN_INFO "\tHooking IMQ after NAT on PREROUTING.\n");
++#endif
++#if defined(CONFIG_IMQ_BEHAVIOR_AB) || defined(CONFIG_IMQ_BEHAVIOR_BB)
++       printk(KERN_INFO "\tHooking IMQ before NAT on POSTROUTING.\n");
++#else
++       printk(KERN_INFO "\tHooking IMQ after NAT on POSTROUTING.\n");
++#endif
++
++       return 0;
++}
++
++static void __exit imq_cleanup_module(void)
++{
++       imq_unhook();
++       imq_cleanup_devs();
++       printk(KERN_INFO "IMQ driver unloaded successfully.\n");
++}
++
++
++module_init(imq_init_module);
++module_exit(imq_cleanup_module);
++
++module_param(numdevs, int, 0);
++MODULE_PARM_DESC(numdevs, "number of IMQ devices (how many imq* devices will be created)");
++MODULE_AUTHOR("http://www.linuximq.net");
++MODULE_DESCRIPTION("Pseudo-driver for the intermediate queue device. See http://www.linuximq.net/ for more information.");
++MODULE_LICENSE("GPL");
+diff -Nru linux-2.6.17.orig/include/linux/imq.h linux-2.6.17/include/linux/imq.h
+--- linux-2.6.17.orig/include/linux/imq.h	1970-01-01 00:00:00.000000000 +0000
++++ linux-2.6.17/include/linux/imq.h	2006-09-06 20:58:51.000000000 +0000
+@@ -0,0 +1,9 @@
++#ifndef _IMQ_H
++#define _IMQ_H
++
++#define IMQ_MAX_DEVS   16
++
++#define IMQ_F_IFMASK   0x7f
++#define IMQ_F_ENQUEUE  0x80
++
++#endif /* _IMQ_H */
+diff -Nru linux-2.6.17.orig/include/linux/netfilter_ipv4/ipt_IMQ.h linux-2.6.17/include/linux/netfilter_ipv4/ipt_IMQ.h
+--- linux-2.6.17.orig/include/linux/netfilter_ipv4/ipt_IMQ.h	1970-01-01 00:00:00.000000000 +0000
++++ linux-2.6.17/include/linux/netfilter_ipv4/ipt_IMQ.h	2006-09-06 20:58:51.000000000 +0000
+@@ -0,0 +1,8 @@
++#ifndef _IPT_IMQ_H
++#define _IPT_IMQ_H
++
++struct ipt_imq_info {
++       unsigned int todev;     /* target imq device */
++};
++
++#endif /* _IPT_IMQ_H */
+diff -Nru linux-2.6.17.orig/include/linux/netfilter_ipv6/ip6t_IMQ.h linux-2.6.17/include/linux/netfilter_ipv6/ip6t_IMQ.h
+--- linux-2.6.17.orig/include/linux/netfilter_ipv6/ip6t_IMQ.h	1970-01-01 00:00:00.000000000 +0000
++++ linux-2.6.17/include/linux/netfilter_ipv6/ip6t_IMQ.h	2006-09-06 20:58:51.000000000 +0000
+@@ -0,0 +1,8 @@
++#ifndef _IP6T_IMQ_H
++#define _IP6T_IMQ_H
++
++struct ip6t_imq_info {
++       unsigned int todev;     /* target imq device */
++};
++
++#endif /* _IP6T_IMQ_H */
+diff -Nru linux-2.6.17.orig/include/linux/skbuff.h linux-2.6.17/include/linux/skbuff.h
+--- linux-2.6.17.orig/include/linux/skbuff.h	2006-06-18 01:49:35.000000000 +0000
++++ linux-2.6.17/include/linux/skbuff.h	2006-09-06 20:58:51.000000000 +0000
<<Diff was trimmed, longer than 597 lines>>


More information about the pld-cvs-commit mailing list