eepro

Grzesiek Sojka grzes w yen.ipipan.waw.pl
Nie, 9 Cze 2002, 17:59:37 CEST



On Sun, 9 Jun 2002, pickman wrote:

> 
> ----- Original Message -----
> From: "pickman" <pickman w wp.pl>
> To: "PLD" <pld-users-pl w pld.org.pl>
> Sent: Saturday, June 08, 2002 7:28 PM
> 
> 
>  Witam
> Niestety znowu o eepro
> 
>  [root w benice root]# cat /etc/sysconfig/interfaces/ifcfg-eth0
>  # name of the device
>  DEVICE=eth0
>  # IP addresses/address prefix
>  # where prefix:
>  # 24 - resembles netmask 255.255.255.0
>  # 16 - resembles netmask 255.255.0.0
>  # etc.
>  # IPADDR may be either IPv4 or IPv6
>  # you may have up to 256 addresses set up
>  IPADDR=192.168.1.1/24
          ^^^^^^^^^^^

> 
>  # you may select which of the above addresses
>  # is primary for this interface (it'd be IPADDR1 in the example below)
>  IP4_PRIM_IF="1"ONBOOT=yes
>  BOOTPROTO=none
> 
>  --<ciach>--
>  reszta jest ustawiona na no
> 
>  --</etc/sysconfig/network>--
>  NETWORKING=yes
>  IPV4_NETWORKING=yes
>  IPV4_FORWARDING=no
>  HOSTNAME="benice"
>  NISDOMAIN="groa"
>  GATEWAY="192.168.1.1"
            ^^^^^^^^^^^

jestes sam dla siebie default getewayem to niedobrze
Te adresy powinny sie roznic badz tytaj nie powinno byc niczego

Pozdrowka
Grze$!?
>  GATEWAYDEV="eth0"
> 
>   ifconfig
>  eth0      Link encap:Ethernet  HWaddr 00:A0:C9:28:15:B9
>            inet6 addr: fe80::2a0:c9ff:fe28:15b9/10 Scope:Link
>            UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
>            RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>            TX packets:0 errors:5 dropped:0 overruns:0 carrier:10
>            collisions:0 txqueuelen:100
>            RX bytes:0 (0.0 b)  TX bytes:358 (358.0 b)
>            Interrupt:5 Base address:0x300
> 
>  [root w benice root]# cat /etc/modules.conf
> alias usb-controller usb-uhci
>  alias eth0 eepro
>  options eepro io=0x300 irq=5
> 
>  [root w benice root]# /etc/rc.d/init.d/network restart
>  Wylaczanie interfejsu eth0.........................................[
>  ZROBIONE ]
>  Ustawianie parametrów sieci........................................[
>  ZROBIONE ]
>  Podnoszenie interfejsu eth0........................................[
>  ZROBIONE ]
>  RTNETLINK answers: Network is unreachable
>  ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
>  ma ktoś jakiś pomysł ???
>  z góry dzieki
>  Łukasz
> 
> 
> 
> ________________________
> http://lists.pld.org.pl/
> 
> 



Więcej informacji o liście dyskusyjnej pld-users-pl