Jak nagrać płytkę > 700MB?

[Michal Kochanowicz]

Hej!

Potrzebuję nagrać płytkę 720MB. Niestety cdrecord się buntuje (poniżej).
Trochę to dziwne, bo niby pisze że płytka ma 826MB, ścieżka 719MB, a bez
overburn nie chce wogóle próbować. A z overburn się wykrzacza.

Nagrywarka to LG32 zflashowana na LG40, płytka to platinium 800MB.

[misiek w wieszak tmp]$ sudo cdrecord -v -dummy -overburn tss.iso
Cdrecord 2.01a14 (i686-pc-linux-gnu) Copyright (C) 1995-2003 Jörg Schilling
TOC Type: 1 = CD-ROM
scsidev: '0,0,0'
scsibus: 0 target: 0 lun: 0
Linux sg driver version: 3.1.24
Using libscg version 'schily-0.7'
Driveropts: 'burnfree'
atapi: 1
Device type    : Removable CD-ROM
Version        : 0
Response Format: 2
Capabilities   :
Vendor_info    : 'HL-DT-ST'
Identifikation : 'CD-RW GCE-8400B '
Revision       : '1.02'
Device seems to be: Generic mmc CD-RW.
Current: 0x0009
Profile: 0x000A
Profile: 0x0009 (current)
Profile: 0x0008
Profile: 0x0002 (current)
Using generic SCSI-3/mmc   CD-R/CD-RW driver (mmc_cdr).
Driver flags   : MMC-2 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R
Drive buf size : 8253696 = 8060 KB
FIFO size      : 8388608 = 8192 KB
Track 01: data   719 MB
Total size:      826 MB (81:50.20) = 368265 sectors
Lout start:      826 MB (81:52/15) = 368265 sectors
Current Secsize: 2048
ATIP info from disk:
  Indicated writing power: 4
  Is not unrestricted
  Is not erasable
  Disk sub type: Medium Type A, low Beta category (A-) (2)
  ATIP start of lead in:  -14888 (96:43/37)
  ATIP start of lead out: 359849 (79:59/74)
Disk type:    unknown dye (reserved id code)
Manuf. index: -1
Manufacturer: unknown (not in table)
Blocks total: 359849 Blocks current: 359849 Blocks remaining: -8416
cdrecord: WARNING: Data may not fit on current disk.
cdrecord: Notice: Overburning active. Trying to write more than the official disk capacity.
Starting to write CD/DVD at speed 40 in dummy TAO mode for single session.
Last chance to quit, starting dummy write    0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
BURN-Free is ON.
Starting new track at sector: 0
Track 01:  702 of  719 MB written (fifo 100%) [buf  99%]  24.1x.cdrecord: Input/output error. write_g1: scsi sendcmd: no error
CDB:  2A 00 00 05 7D 89 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 0A 00 00 00 00 63 00 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x63 Qual 0x00 (end of user area encountered on this track) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.013s timeout 40s

write track data: error after 736905216 bytes
cdrecord: A write error occured.
cdrecord: Please properly read the error message above.
Writing  time:  220.365s
Average write speed  22.3x.
Min drive buffer fill was 99%
Fixating...
WARNING: Some drives don't like fixation in dummy mode.
Fixating time:   22.340s
BURN-Free was never needed.
cdrecord: fifo had 11735 puts and 11608 gets.
cdrecord: fifo was 0 times empty and 6385 times full, min fill was 59%.
[misiek w wieszak tmp]$
-- 
--= Michal Kochanowicz =--==--==BOFH==--==--= michal w michal.waw.pl =--
--= finger me for PGP public key or visit http://michal.waw.pl/PGP =--
--==--==--==--==--==-- Vodka. Connecting people.--==--==--==--==--==--
A chodzenie po górach SSIE!!!