PLD AC i nie widzi mi 4GB pamieci RAM
Pawel Koska
pawel w artfan.net
Pon, 12 Cze 2006, 14:12:10 CEST
Dnia niedziela, 11 czerwca 2006 10:46, Marcin Meller napisał:
> > Jakoś nie mogę czegoś takiego co mogło by to przypominać, namierzyć w
> > dmesgu, ani w syslogu i innych. Może po prostu to mi gdzieś umyka...
>
> dmesg |more
>
> bodajrze czwarta linkijka
Ja tam nie mogę znaleźć, nie znam się ;-)
Pozwolę sobie wrzucić cały dmesg.
Paweł
-------------- następna część ---------
specific routine.. 5599.88 BogoMIPS (lpj=11199763)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000641d 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 20100000 00000000 00000000 0000641d 00000000 00000000
monitor/mwait feature present.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfebfbff 20100000 00000000 00000080 0000641d 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (24) available
CPU1: Intel(R) Pentium(R) D CPU 2.80GHz stepping 04
Total of 2 processors activated (11204.92 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG
ACPI: Subsystem revision 20050902
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
Boot video device is 0000:00:02.0
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 *11 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 *9 10 11 12)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 *10 11 12)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX5._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
TC classifier action (bugs to netdev w vger.kernel.org cc hadi w cyberus.ca)
pnp: 00:05: ioport range 0x500-0x53f has been reserved
pnp: 00:05: ioport range 0x400-0x47f could not be reserved
pnp: 00:05: ioport range 0x680-0x6ff has been reserved
PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
PCI: Bridge: 0000:00:1c.0
IO window: 1000-1fff
MEM window: e0100000-e01fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.2
IO window: disabled.
MEM window: e0300000-e03fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.3
IO window: disabled.
MEM window: e0400000-e04fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.4
IO window: disabled.
MEM window: e0500000-e05fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.5
IO window: disabled.
MEM window: e0600000-e06fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
IO window: disabled.
MEM window: e0000000-e00fffff
PREFETCH window: disabled.
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1c.2 to 64
ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1c.3 to 64
ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 17 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1c.4 to 64
ACPI: PCI Interrupt 0000:00:1c.5[B] -> GSI 16 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:1c.5 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
Machine check exception polling timer started.
audit: initializing netlink socket (disabled)
audit(1150108873.588:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Allocate Port Service[pcie02]
Allocate Port Service[pcie03]
ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1c.2 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Allocate Port Service[pcie02]
Allocate Port Service[pcie03]
ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1c.3 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Allocate Port Service[pcie02]
Allocate Port Service[pcie03]
ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 17 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1c.4 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Allocate Port Service[pcie02]
Allocate Port Service[pcie03]
ACPI: PCI Interrupt 0000:00:1c.5[B] -> GSI 16 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:1c.5 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Allocate Port Service[pcie02]
Allocate Port Service[pcie03]
Real Time Clock Driver v1.12
hpet_acpi_add: no address or irqs in _CRS
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
mice: PS/2 mouse device common for all mice
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 7, 524288 bytes)
TCP established hash table entries: 524288 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 524288 bind 65536)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
RAMDISK: Compressed image found at block 0
input: AT Translated Set 2 keyboard on isa0060/serio0
VFS: Mounted root (romfs filesystem) readonly.
md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 3.39
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
SCSI subsystem initialized
libata version 1.12 loaded.
ahci version 1.01
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ahci(0000:00:1f.2) AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl RAID mode
ahci(0000:00:1f.2) flags: 64bit ncq led clo pio slum part
ata1: SATA max UDMA/133 cmd 0xF8818100 ctl 0x0 bmdma 0x0 irq 58
ata2: SATA max UDMA/133 cmd 0xF8818180 ctl 0x0 bmdma 0x0 irq 58
ata3: SATA max UDMA/133 cmd 0xF8818200 ctl 0x0 bmdma 0x0 irq 58
ata4: SATA max UDMA/133 cmd 0xF8818280 ctl 0x0 bmdma 0x0 irq 58
ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:207f
ata1: dev 0 ATA, max UDMA/133, 488397168 sectors: lba48
ata1: dev 0 configured for UDMA/133
scsi0 : ahci
ata2: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:207f
ata2: dev 0 ATA, max UDMA/133, 488397168 sectors: lba48
ata2: dev 0 configured for UDMA/133
scsi1 : ahci
ata3: no device found (phy stat 00000000)
scsi2 : ahci
ata4: no device found (phy stat 00000000)
scsi3 : ahci
Vendor: ATA Model: ST3250624AS Rev: 3.AA
Type: Direct-Access ANSI SCSI revision: 05
Vendor: ATA Model: ST3250624AS Rev: 3.AA
Type: Direct-Access ANSI SCSI revision: 05
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH7: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 177
ICH7: chipset revision 1
ICH7: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x20b0-0x20b7, BIOS settings: hda:DMA, hdb:pio
Probing IDE interface ide0...
hda: HL-DT-ST DVDRAM GSA-4167B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sdb: drive cache: write back
SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sdb: drive cache: write back
sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 sdb6 sdb7 >
Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
md: md0 stopped.
md: bind<sdb2>
md: bind<sda2>
raid1: raid set md0 active with 2 out of 2 mirrors
ReiserFS: md0: found reiserfs format "3.6" with standard journal
ReiserFS: md0: using ordered data mode
ReiserFS: md0: journal params: device md0, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: md0: checking transaction log (md0)
ReiserFS: md0: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Trying to move old root to /initrd ... okay
Freeing unused kernel memory: 244k freed
hda: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 66
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 66, io base 0x00002080
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 185, io base 0x00002060
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 177, io base 0x00002040
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 193, io base 0x00002020
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 66
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: irq 66, io mem 0xe02c4400
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
Adding 2000052k swap on /dev/sda1. Priority:1 extents:1 across:2000052k
Adding 2000052k swap on /dev/sdb1. Priority:1 extents:1 across:2000052k
logips2pp: Detected unknown logitech mouse model 85
input: ImExPS/2 Logitech Explorer Mouse on isa0060/serio1
md: md1 stopped.
md: bind<sdb3>
md: bind<sda3>
raid1: raid set md1 active with 2 out of 2 mirrors
md: md2 stopped.
md: bind<sdb5>
md: bind<sda5>
raid1: raid set md2 active with 2 out of 2 mirrors
md: md3 stopped.
md: bind<sdb6>
md: bind<sda6>
md3: setting max_sectors to 128, segment boundary to 32767
raid0: looking at sda6
raid0: comparing sda6(6249152) with sda6(6249152)
raid0: END
raid0: ==> UNIQUE
raid0: 1 zones
raid0: looking at sdb6
raid0: comparing sdb6(6249152) with sda6(6249152)
raid0: EQUAL
raid0: FINAL 1 zones
raid0: done.
raid0 : md_size is 12498304 blocks.
raid0 : conf->hash_spacing is 12498304 blocks.
raid0 : nb_zone is 1.
raid0 : Allocating 4 bytes for hash.
md: md4 stopped.
md: bind<sdb7>
md: bind<sda7>
raid1: raid set md4 active with 2 out of 2 mirrors
ReiserFS: md1: found reiserfs format "3.6" with standard journal
ReiserFS: md1: using ordered data mode
ReiserFS: md1: journal params: device md1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: md1: checking transaction log (md1)
ReiserFS: md1: Using r5 hash to sort names
ReiserFS: md2: found reiserfs format "3.6" with standard journal
ReiserFS: md2: using ordered data mode
ReiserFS: md2: journal params: device md2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: md2: checking transaction log (md2)
ReiserFS: md2: Using r5 hash to sort names
ReiserFS: md3: found reiserfs format "3.6" with standard journal
ReiserFS: md3: using ordered data mode
ReiserFS: md3: journal params: device md3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: md3: checking transaction log (md3)
ReiserFS: md3: Using r5 hash to sort names
ReiserFS: md4: found reiserfs format "3.6" with standard journal
ReiserFS: md4: using ordered data mode
ReiserFS: md4: journal params: device md4, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: md4: checking transaction log (md4)
ReiserFS: md4: Using r5 hash to sort names
Intel(R) PRO/1000 Network Driver - version 6.0.60-k2-NAPI
Copyright (c) 1999-2005 Intel Corporation.
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:01:00.0 to 64
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
e1000: eth0: e1000_watchdog_task: NIC Link is Up 1000 Mbps Full Duplex
NET: Registered protocol family 10
Disabled Privacy Extensions on device c03a8e80(lo)
IPv6 over IPv4 tunneling driver
Installing knfsd (copyright (C) 1996 okir w monad.swb.de).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: starting 90-second grace period
eth0: no IPv6 routers present
Więcej informacji o liście dyskusyjnej pld-users-pl