[TH] xorg.conf dla LG 915FT
Arkadiusz Chomicki
chomar w assat.pl
Wto, 27 Maj 2008, 20:00:54 CEST
witam
posiadam monitor LG Flatron 915FT
Monitor ten ma mozliwosc pracy w rozdzielczosci 1600x1200 w 85Hz
niestety po upgrade do Th nie udaje mi sie ustawic wiecej niz 1152x864 w 75Hz
A do tego ciekawostka jest taka ze wogole nie X11 nie bierze pod uwage
teg co wpisze w seksji "Screen->Display"
Moze macie jakies pomysly?
Proszę o pomoc.
Moje ustawienia w xorg.conf:
Section "Monitor"
Identifier "LG Flatron 915FT+"
HorizSync 30-110
VertRefresh 50-200
EndSection
Section "Device"
Identifier "Matrox Millennium G400"
Driver "mga"
Option "HWCursor" "off"
EndSection
Section "Screen"
Identifier "Screen 1"
Device "Matrox Millennium G400"
Monitor "LG Flatron 915FT+"
DefaultDepth 24
Subsection "Display"
Depth 8
Modes "1600x1200" "1400x1050" "1024x768" "800x600" "640x480"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 16
Modes "1600x1200" "1400x1050" "1024x768" "800x600" "640x480"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 24
Modes "1600x1200" "1400x1050" "1024x768" "800x600" "640x480"
ViewPort 0 0
EndSubsection
EndSection
Wyciag z Log:
(--) PCI:*(1:0:0) Matrox Graphics, Inc. MGA G400/G450 rev 133, Mem @
0xf0000000/25, 0xf3200000/14, 0xf2800000/23
(II) LoadModule: "mga"
(II) Loading /usr/lib/xorg/modules/drivers//mga_drv.so
(II) Module mga: vendor="X.Org Foundation"
(II) MGA: driver for Matrox chipsets: mga2064w, mga1064sg, mga2164w,
mga2164w AGP, mgag100, mgag100 PCI, mgag200, mgag200 PCI,
mgag200 SE A PCI, mgag200 SE B PCI, mgag400, mgag550
(--) Chipset mgag400 found
(--) MGA(0): Chipset: "mgag400" (G450)
(**) MGA(0): Depth 24, (--) framebuffer bpp 32
(==) MGA(0): RGB weight 888
(**) MGA(0): Option "HWcursor" "off"
(==) MGA(0): Using AGP 1x mode
(==) MGA(0): Using XAA acceleration
(--) MGA(0): Linear framebuffer at 0xF0000000
(**) MGA(0): MMIO registers at 0xF3200000
(--) MGA(0): Pseudo-DMA transfer window at 0xF2800000
(==) MGA(0): BIOS at 0xC0000
(--) MGA(0): Video BIOS info block at offset 0x07CC0
(**) MGA(0): VideoRAM: 131072 kByte
(II) MGA(0): I2C bus "DDC P1" initialized.
(II) MGA(0): I2C bus "DDC P2" initialized.
(II) MGA(0): Output DVI using monitor section LG Flatron 915FT+
(II) MGA(0): Output VGA has no monitor section
(==) MGA(0): Write-combining range (0xf0000000,0x8000000)
(==) MGA(0): Removed MMIO write-combining range (0xf0000000,0x8000000)
(II) MGA(0): I2C device "DDC P1:ddc2" registered at address 0xA0.
(II) MGA(0): I2C device "DDC P1:ddc2" removed.
(II) MGA(0): I2C device "DDC P2:ddc2" registered at address 0xA0.
(II) MGA(0): EDID vendor "GSM", prod id 19021
(II) MGA(0): Output DVI connected
(II) MGA(0): Output VGA connected
(II) MGA(0): Output DVI using initial mode 1152x768
(II) MGA(0): Output VGA using initial mode 1152x864
(==) MGA(0): Using gamma correction (1.0, 1.0, 1.0)
(==) MGA(0): Min pixel clock is 17 MHz
(--) MGA(0): Max pixel clock is 1200 MHz
(--) MGA(0): Has SDRAM
(--) MGA(0): Virtual size is 1600x1024 (pitch 0)
(**) MGA(0): Default mode "1152x768": 65.0 MHz (scaled from 0.0 MHz),
44.2 kHz, 54.8 Hz
(II) MGA(0): Modeline "1152x768"x54.8 65.00 1152 1178 1314 1472 768
771 777 806 +hsync +vsync (44.2 kHz)
(**) MGA(0): Default mode "1024x768": 94.5 MHz (scaled from 0.0 MHz),
68.7 kHz, 85.0 Hz
(II) MGA(0): Modeline "1024x768"x85.0 94.50 1024 1072 1168 1376 768
769 772 808 +hsync +vsync (68.7 kHz)
(**) MGA(0): Default mode "1024x768": 78.8 MHz (scaled from 0.0 MHz),
60.0 kHz, 75.0 Hz
(II) MGA(0): Modeline "1024x768"x75.0 78.75 1024 1040 1136 1312 768
769 772 800 +hsync +vsync (60.0 kHz)
(**) MGA(0): Default mode "1024x768": 75.0 MHz (scaled from 0.0 MHz),
56.5 kHz, 70.1 Hz
(II) MGA(0): Modeline "1024x768"x70.1 75.00 1024 1048 1184 1328 768
771 777 806 -hsync -vsync (56.5 kHz)
(**) MGA(0): Default mode "1024x768": 65.0 MHz (scaled from 0.0 MHz),
48.4 kHz, 60.0 Hz
(II) MGA(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768
771 777 806 -hsync -vsync (48.4 kHz)
(**) MGA(0): Default mode "832x624": 57.3 MHz (scaled from 0.0 MHz),
49.7 kHz, 74.6 Hz
(II) MGA(0): Modeline "832x624"x74.6 57.28 832 864 928 1152 624 625
628 667 -hsync -vsync (49.7 kHz)
(**) MGA(0): Default mode "800x600": 56.3 MHz (scaled from 0.0 MHz),
53.7 kHz, 85.1 Hz
(II) MGA(0): Modeline "800x600"x85.1 56.30 800 832 896 1048 600 601
604 631 +hsync +vsync (53.7 kHz)
(**) MGA(0): Default mode "800x600": 50.0 MHz (scaled from 0.0 MHz),
48.1 kHz, 72.2 Hz
(II) MGA(0): Modeline "800x600"x72.2 50.00 800 856 976 1040 600 637
643 666 +hsync +vsync (48.1 kHz)
(**) MGA(0): Default mode "800x600": 49.5 MHz (scaled from 0.0 MHz),
46.9 kHz, 75.0 Hz
(II) MGA(0): Modeline "800x600"x75.0 49.50 800 816 896 1056 600 601
604 625 +hsync +vsync (46.9 kHz)
(**) MGA(0): Default mode "800x600": 40.0 MHz (scaled from 0.0 MHz),
37.9 kHz, 60.3 Hz
(II) MGA(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601
605 628 +hsync +vsync (37.9 kHz)
(**) MGA(0): Default mode "800x600": 36.0 MHz (scaled from 0.0 MHz),
35.2 kHz, 56.2 Hz
(II) MGA(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601
603 625 +hsync +vsync (35.2 kHz)
(**) MGA(0): Default mode "640x480": 36.0 MHz (scaled from 0.0 MHz),
43.3 kHz, 85.0 Hz
(II) MGA(0): Modeline "640x480"x85.0 36.00 640 696 752 832 480 481
484 509 -hsync -vsync (43.3 kHz)
(**) MGA(0): Default mode "640x480": 31.5 MHz (scaled from 0.0 MHz),
37.9 kHz, 72.8 Hz
(II) MGA(0): Modeline "640x480"x72.8 31.50 640 664 704 832 480 489
492 520 -hsync -vsync (37.9 kHz)
(**) MGA(0): Default mode "640x480": 31.5 MHz (scaled from 0.0 MHz),
37.5 kHz, 75.0 Hz
(II) MGA(0): Modeline "640x480"x75.0 31.50 640 656 720 840 480 481
484 500 -hsync -vsync (37.5 kHz)
(**) MGA(0): Default mode "640x480": 25.2 MHz (scaled from 0.0 MHz),
31.5 kHz, 59.9 Hz
(II) MGA(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490
492 525 -hsync -vsync (31.5 kHz)
(**) MGA(0): Default mode "720x400": 35.5 MHz (scaled from 0.0 MHz),
37.9 kHz, 85.0 Hz
(II) MGA(0): Modeline "720x400"x85.0 35.50 720 756 828 936 400 401
404 446 -hsync +vsync (37.9 kHz)
(**) MGA(0): Default mode "640x400": 31.5 MHz (scaled from 0.0 MHz),
37.9 kHz, 85.1 Hz
(II) MGA(0): Modeline "640x400"x85.1 31.50 640 672 736 832 400 401
404 445 -hsync +vsync (37.9 kHz)
(**) MGA(0): Default mode "640x350": 31.5 MHz (scaled from 0.0 MHz),
37.9 kHz, 85.1 Hz
(II) MGA(0): Modeline "640x350"x85.1 31.50 640 672 736 832 350 382
385 445 +hsync -vsync (37.9 kHz)
(**) MGA(0): Default mode "1600x1024": 106.9 MHz (scaled from 0.0 MHz),
64.0 kHz, 60.0 Hz
(II) MGA(0): Modeline "1600x1024"x60.0 106.91 1600 1620 1640 1670
1024 1027 1030 1067 -hsync -vsync (64.0 kHz)
(**) MGA(0): Default mode "1280x1024": 157.5 MHz (scaled from 0.0 MHz),
91.1 kHz, 85.0 Hz
(II) MGA(0): Modeline "1280x1024"x85.0 157.50 1280 1344 1504 1728
1024 1025 1028 1072 +hsync +vsync (91.1 kHz)
(**) MGA(0): Default mode "1280x1024": 135.0 MHz (scaled from 0.0 MHz),
80.0 kHz, 75.0 Hz
(II) MGA(0): Modeline "1280x1024"x75.0 135.00 1280 1296 1440 1688
1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
(**) MGA(0): Default mode "1280x1024": 108.0 MHz (scaled from 0.0 MHz),
64.0 kHz, 60.0 Hz
(II) MGA(0): Modeline "1280x1024"x60.0 108.00 1280 1328 1440 1688
1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(**) MGA(0): Default mode "1280x960": 148.5 MHz (scaled from 0.0 MHz),
85.9 kHz, 85.0 Hz
(II) MGA(0): Modeline "1280x960"x85.0 148.50 1280 1344 1504 1728 960
961 964 1011 +hsync +vsync (85.9 kHz)
(**) MGA(0): Default mode "1280x960": 108.0 MHz (scaled from 0.0 MHz),
60.0 kHz, 60.0 Hz
(II) MGA(0): Modeline "1280x960"x60.0 108.00 1280 1376 1488 1800 960
961 964 1000 +hsync +vsync (60.0 kHz)
(**) MGA(0): Default mode "1152x864": 108.0 MHz (scaled from 0.0 MHz),
67.5 kHz, 75.0 Hz
(II) MGA(0): Modeline "1152x864"x75.0 108.00 1152 1216 1344 1600 864
865 868 900 +hsync +vsync (67.5 kHz)
(==) MGA(0): DPI set to (75, 75)
(II) MGA(0): YDstOrg is set to 0
(==) MGA(0): Write-combining range (0xf0000000,0x8000000)
(==) MGA(0): Removed MMIO write-combining range (0xf0000000,0x8000000)
(II) MGA(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(--) MGA(0): 16 DWORD fifo
(==) MGA(0): Default visual is TrueColor
(II) MGA(0): [drm] bpp: 32 depth: 24
(II) MGA(0): [drm] Sarea 2200+664: 2864
[drm] failed to load kernel module "mga"
(EE) MGA(0): [drm] DRIScreenInit failed. Disabling DRI.
(II) MGA(0): Using 1597 lines for offscreen memory.
(II) MGA(0): Using XFree86 Acceleration Architecture (XAA)
(==) MGA(0): Backing store disabled
(==) MGA(0): Silken mouse enabled
(II) MGA(0): RandR 1.2 enabled, ignore the following RandR disabled message.
(II) MGA(0): Using overlay video
(WW) MGA(0): Direct rendering disabled
(II) MGA(0): Setting screen physical size to 304 x 228
--
Arkadiusz Chomicki
Wladyslawowo
Więcej informacji o liście dyskusyjnej pld-users-pl