[Ac] eagle-usb.spec

[Sławomir Sędyka]

Próba zbudowania eagle-usb.spec z brancha Ac kończy się tak:

configure: creating ./config.status
config.status: creating Makefile.common
config.status: WARNING:  Makefile.common.in seems to ignore the 
--datarootdir setting
config.status: executing default commands

========================================================================
distribution detected                           generic

dhcp support                                    no

pppd support                                    yes
   pppoa support                                 yes
   pppoe support                                 yes

install eagleconnect (tcl/tk frontend)          no

generate documentation                          yes
========================================================================

error: kernel-sources cannot be found!

warning: kernel-sources version is different from the current kernel.

warning: a previous eagle-usb driver was found on your system.
          You should run 'make uninstall' now.

+ /usr/bin/make -C driver/firmware CC=i686-pld-linux-gcc OPT=-O2 -march=i686
make: Entering directory 
`/home/users/kermit/rpm/BUILD/eagle-usb-2.3.3/driver/firmware'
i686-pld-linux-gcc -O2 -march=i686  -pipe -Wall -pedantic builddsp.c -o 
buildDSP
./buildDSP -d sagem/pots dsp_code_pots.bin
Reading file sagem/pots/rtbldep0.bnm
Reading file sagem/pots/rtbldep1.bnm
Reading file sagem/pots/rtbldep2.bnm
Reading file sagem/pots/rtbldep3.bnm
Reading file sagem/pots/rtbldep4.bnm
Writing file dsp_code_pots.bin
./buildDSP -d sagem/isdn dsp_code_isdn.bin
Reading file sagem/isdn/rtbldei0.bnm
Reading file sagem/isdn/rtbldei1.bnm
Reading file sagem/isdn/rtbldei2.bnm
Reading file sagem/isdn/rtbldei3.bnm
Reading file sagem/isdn/rtbldei4.bnm
Writing file dsp_code_isdn.bin
make: Leaving directory 
`/home/users/kermit/rpm/BUILD/eagle-usb-2.3.3/driver/firmware'
+ /usr/bin/make -C driver/user CC=i686-pld-linux-gcc OPT=-O2 -march=i686
make: Entering directory 
`/home/users/kermit/rpm/BUILD/eagle-usb-2.3.3/driver/user'
i686-pld-linux-gcc -O2 -march=i686  -pipe -Wall -pedantic -DLINUX -g 
-DCONF_DIR="\"/etc/eagle-usb\"" -DBIN_DIR="\"/usr/share/misc\"" 
'-DEAGLEUSBVERSION="2.3.3"' -DUSE_CMVS eaglectrl.c -o eaglectrl
In file included from ../eagle-usb.h:30,
                  from eaglectrl.c:40:
../eu_types.h:29:24: asm/bitops.h: Nie ma takiego pliku ani katalogu
make: *** [eaglectrl] Error 1
make: Leaving directory 
`/home/users/kermit/rpm/BUILD/eagle-usb-2.3.3/driver/user'
błąd: Błędny status wyjścia z /home/users/kermit/tmp/rpm-tmp.63749 (%build)


Błędy budowania RPM-a:
     Błędny status wyjścia z /home/users/kermit/tmp/rpm-tmp.63749 (%build)
Error: package build failed. (no more info)

rpm -qa kernel\*
kernel-usb-eagle-2.3.3-62.i686
kernel-module-build-2.6.16.62-1.i686
kernel-headers-2.6.16.62-1.i686
kernel-source-2.6.16.62-1.i686
kernel-2.6.16.60-11.i686

Niech Ktoś[TM] na to spojrzy i poprawi. Z góry dzięki.

P.S. Jak zgłosić błąd na LP skoro:
"eagle-usb" does not exist in PLD Linux. Please choose a different 
package. If you're unsure, please select "I don't know"

-- 
Sławomir Sędyka