smart problem 2
lord_Niedzwiedz
sir_Misiek w o2.pl
Pią, 27 Lis 2015, 14:22:14 CET
A co oznaczają takie komunikaty jak poniżej ??
Jest ok, czy nie ??
[root w Misiek /Wymiana]# smartctl -a /dev/sda
smartctl 6.4 2015-06-04 r4109 [x86_64-linux-4.2.6-1] (local build)
Copyright (C) 2002-15, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Maxtor MaXLine Plus II
Device Model: Maxtor 7Y250M0
Serial Number: Y66EJFGE
Firmware Version: YAR51HW0
User Capacity: 250,058,268,160 bytes [250 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA/ATAPI-7 T13/1532D revision 0
Local Time is: Fri Nov 27 14:20:27 2015 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x85) Offline data collection activity
was aborted by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 39) The self-test routine was
interrupted
by the host with a hard or soft reset.
Total time to complete Offline
data collection: ( 363) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 106) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
WHEN_FAILED RAW_VALUE
3 Spin_Up_Time 0x0027 179 179 063 Pre-fail
Always - 19999
4 Start_Stop_Count 0x0032 253 253 000 Old_age
Always - 666
5 Reallocated_Sector_Ct 0x0033 253 253 063 Pre-fail
Always - 0
6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail
Offline - 0
7 Seek_Error_Rate 0x000a 253 252 000 Old_age
Always - 0
8 Seek_Time_Performance 0x0027 250 243 187 Pre-fail
Always - 57955
9 Power_On_Minutes 0x0032 163 163 000 Old_age
Always - 734h+43m
10 Spin_Retry_Count 0x002b 253 252 157 Pre-fail
Always - 0
11 Calibration_Retry_Count 0x002b 253 252 223 Pre-fail
Always - 0
12 Power_Cycle_Count 0x0032 250 250 000 Old_age
Always - 1265
192 Power-Off_Retract_Count 0x0032 253 253 000 Old_age
Always - 0
193 Load_Cycle_Count 0x0032 253 253 000 Old_age
Always - 0
194 Temperature_Celsius 0x0032 253 253 000 Old_age
Always - 45
195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age
Always - 2455
196 Reallocated_Event_Count 0x0008 253 253 000 Old_age
Offline - 0
197 Current_Pending_Sector 0x0008 253 253 000 Old_age
Offline - 0
198 Offline_Uncorrectable 0x0008 253 253 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x0008 063 001 000 Old_age
Offline - 8463
200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age
Always - 0
201 Soft_Read_Error_Rate 0x000a 253 252 000 Old_age
Always - 4
202 Data_Address_Mark_Errs 0x000a 253 252 000 Old_age
Always - 0
203 Run_Out_Cancel 0x000b 253 252 180 Pre-fail
Always - 0
204 Soft_ECC_Correction 0x000a 253 252 000 Old_age
Always - 0
205 Thermal_Asperity_Rate 0x000a 253 252 000 Old_age
Always - 0
207 Spin_High_Current 0x002a 253 252 000 Old_age
Always - 0
208 Spin_Buzz 0x002a 253 252 000 Old_age
Always - 0
209 Offline_Seek_Performnce 0x0024 195 195 000 Old_age
Offline - 0
99 Unknown_Attribute 0x0004 253 253 000 Old_age
Offline - 0
100 Unknown_Attribute 0x0004 253 253 000 Old_age
Offline - 0
101 Unknown_Attribute 0x0004 253 253 000 Old_age
Offline - 0
SMART Error Log Version: 1
Warning: ATA error count 9674 inconsistent with error log pointer 5
ATA Error Count: 9674 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 9674 occurred at disk power-on lifetime: 29360 hours (1223 days +
8 hours)
When the command that caused the error occurred, the device was in an
unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 85 24 e3 70 e0 Error: ICRC, ABRT 133 sectors at LBA =
0x0070e324 = 7398180
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
35 00 00 a9 e1 70 e0 00 05:49:13.536 WRITE DMA EXT
27 00 00 00 00 00 e0 00 05:49:13.536 READ NATIVE MAX ADDRESS
EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 05:49:13.536 IDENTIFY DEVICE
ef 03 42 00 00 00 a0 00 05:49:13.536 SET FEATURES [Set transfer
mode]
27 00 00 00 00 00 e0 00 05:49:13.536 READ NATIVE MAX ADDRESS
EXT [OBS-ACS-3]
Error 9673 occurred at disk power-on lifetime: 29360 hours (1223 days +
8 hours)
When the command that caused the error occurred, the device was in an
unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 cc dd e4 70 e0 Error: ICRC, ABRT 204 sectors at LBA =
0x0070e4dd = 7398621
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
35 00 00 a9 e1 70 e0 00 05:49:13.040 WRITE DMA EXT
35 00 00 a9 f1 6e e0 00 05:49:13.040 WRITE DMA EXT
35 00 00 a9 75 6e e0 00 05:49:13.024 WRITE DMA EXT
35 00 00 a9 71 6e e0 00 05:49:13.024 WRITE DMA EXT
35 00 00 a9 89 6d e0 00 05:49:13.024 WRITE DMA EXT
Error 9672 occurred at disk power-on lifetime: 29360 hours (1223 days +
8 hours)
When the command that caused the error occurred, the device was in an
unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 42 67 42 72 e0 Error: ICRC, ABRT 66 sectors at LBA =
0x00724267 = 7488103
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
35 00 00 a9 41 72 e0 00 05:48:19.024 WRITE DMA EXT
35 00 00 a9 29 70 e0 00 05:48:19.008 WRITE DMA EXT
ea 00 00 d5 22 0d a0 00 05:48:19.008 FLUSH CACHE EXT
ca 00 08 ce 22 0d e5 00 05:48:19.008 WRITE DMA
ea 00 00 a8 61 6f a0 00 05:48:18.928 FLUSH CACHE EXT
Error 9671 occurred at disk power-on lifetime: 29360 hours (1223 days +
8 hours)
When the command that caused the error occurred, the device was in an
unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 1b 8e 60 6e e0 Error: ICRC, ABRT 27 sectors at LBA =
0x006e608e = 7233678
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
35 00 00 a9 59 6e e0 00 05:48:18.464 WRITE DMA EXT
27 00 00 00 00 00 e0 00 05:48:18.464 READ NATIVE MAX ADDRESS
EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 05:48:18.448 IDENTIFY DEVICE
ef 03 42 00 00 00 a0 00 05:48:18.448 SET FEATURES [Set transfer
mode]
27 00 00 00 00 00 e0 00 05:48:18.448 READ NATIVE MAX ADDRESS
EXT [OBS-ACS-3]
Error 9670 occurred at disk power-on lifetime: 29360 hours (1223 days +
8 hours)
When the command that caused the error occurred, the device was in an
unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 42 67 5a 6e e0 Error: ICRC, ABRT 66 sectors at LBA =
0x006e5a67 = 7232103
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
35 00 00 a9 59 6e e0 00 05:48:17.984 WRITE DMA EXT
35 00 00 a9 91 6d e0 00 05:48:17.984 WRITE DMA EXT
35 00 00 a9 31 6d e0 00 05:48:17.984 WRITE DMA EXT
ea 00 00 80 76 a5 a0 00 05:48:17.360 FLUSH CACHE EXT
35 00 08 79 76 a5 e0 00 05:48:17.360 WRITE DMA EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining
LifeTime(hours) LBA_of_first_error
# 1 Extended offline Interrupted (host reset) 70% 29360 -
# 2 Extended offline Completed without error 00% 22672 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Więcej informacji o liście pld-users-pl